Transportni trak s cepiči

AGRIFON

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2005, obratovalne ure: 30.408 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 50 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.250 mm, širina bale: 1.100 mm, višina bale: 720 mm, teža bale: 550 kg, skupna masa: 16.000 kg, kapaciteta rezervoarja za olje: 600 l, leto zadnje generalne obnove: 2024, Technical Specifications of the Baler: Manufacturer: Presona AB Model: LP 50 EH1 Year of manufacture: 2005 Operating hours: 30,408 hours (as of April) Number of bales produced: 198,059 (as of April) Main press force: 50 t Specific press force: 63 N/cm² Theoretical throughput: 530 m³/hour Throughput under working conditions: 260 m³/hour Feed hopper dimensions: 1,250 x 1,100 mm Press chamber volume: 2.2 m³ Bale dimensions: 1,100 x 720 mm, length variable Drive power: 22 kW Tying: 5-fold vertical, fully automatic Throughput rates at bulk density of: 30 kg/m³: 6 to 7 t/hour 50 kg/m³: 7 to 9 t/hour 100 kg/m³: 11 to 14 t/hour Bale density (paper/newspaper): 400 to 550 kg/m³ Hydraulic oil tank capacity: 600 L PLC control: Telemecanique TSX Micro Control panel: Schneider Magelis Effective transport dimensions (excluding baler): 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight (baler): approx. 16 t Condition of the baler: The machine has been partially overhauled in our workshop and general maintenance work has been carried out. After completion of the overhaul, the baler was tested during operation and is available for sale at short notice. The following overhaul work was performed: General: - Machine cleaned, derusted, primed, and partially repainted - Wire entry marks in the press channel guideways welded and smoothed Hydraulic unit: - Hydraulic oil tank drained, tank cleaned, new oil filled - Oil filter and air filter replaced - Leaking oil sight glass on hydraulic oil tank replaced - All hydraulic hoses replaced Electrics: - Menu language set to English in the program - Two key switches on the control panel replaced - Control cabinet replaced - Signal lamp on the control cabinet replaced - Limit switch for the flap replaced - Electrics of the wirbulator renewed, connected, and tested Press ram: - All four guide rollers of the press ram removed and replaced - Main hydraulic cylinder dismantled, disassembled, and partially overhauled; cylinder barrel honed, complete seal set replaced, leak test carried out - All plastic wear pads on the press ram replaced Pre-press flap: - Both bearings on pre-press shaft replaced - Both hydraulic cylinders dismantled, disassembled, and partially overhauled; both cylinder barrels honed, complete seal sets replaced, leak test carried out - Scraper flap on pre-press replaced Tying unit: - Two complete needles with wire guide rollers replaced - Needles adjusted and set - All wire guide rollers in the needle heads replaced Gcjdpju Thhrefx Ab Toa - Twister fingers replaced - Two twister shafts replaced - All 8 wear plates on the twist mechanism under the twister fingers replaced Scope of delivery: Only the baler is being sold. Documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. Inspection by appointment. We assume no liability for the technical details or possible errors.

Leto izdelave: 2023, Stanje: novo, For sale: Alligator shear / cable shear, also suitable for metal processing. Gcsdpfx Abeku Ag Se Toa Model: AS/250 Max. Shear Force: 250 kN Cutting Length: 300 mm Max. Opening: 160 mm Hydraulic Pressure: 15 MPa Full Cycles per Minute: 10–15 cycles/min Power Consumption: 5.5 kW Weight: 450 kg Dimensions (L×W×H): 1200 × 980 × 1200 mm

Leto izdelave: 2020, Stanje: novo, DESCRIPTION The so-called half water is produced from the demineralized water station using ion exchange technology. The station consists of 3 columns: - Strongly acidic cation exchanger operated in the sodium cycle, Gcjdpefz Nakjfx Ab Tja - Strongly basic anion exchanger operated in the chloride cycle, - Carbon filter Our demineralization stations RDI-2 / RDI-4 are equipped with fully automatic control heads. Pipes The columns are made of AISI316L stainless steel.

Leto izdelave: 2023, Stanje: novo, Fine grinding mill for flour, coffee, dried spices, and more. Grinding range from 20 to 120 mesh. Throughput: 100–400 kg per hour. Motor speed: 3,400 rpm. Machine weight: 600 kg. Required power: 11 kW. The machine is equipped with an additional dust extraction filtration unit. Constructed entirely from SUS304 stainless steel. Godpfxsk S Rpuj Ab Teca

Leto izdelave: 2018, Stanje: kot nova (razstavni stroj),

Stanje: novo, številka stroja/vozila: NEW-83, Vehicle Transporter Mercedes Benz Atego Rear Axle Air Suspension * PTO (Power Take-Off) * Cab with 2 individual seats * Sleeping compartment * Auxiliary heater * Radio/CD * Digital tachograph (EC control device) * Lowerable tail section Car transporter body DS12 [MODULO]: Double-decker superstructure for transporting 2 passenger cars or 1 small van or motorhome * Loading area lower deck approx. 700 x 255 cm * Lifting deck approx. 450 x 240 cm * Cable winch with wireless and wired remote control * Body hot-dip galvanized Trailer: Air-braked BLYSS trailer for 3 passenger cars * Payload approx. 11,000 kg * Loading area approx. 890 x 255 cm * Rear section extendable by approx. 150 cm * Lifting deck approx. 450 x 240 cm * BPW axles * ABS * Trailer with perforated drive-on plates * Vehicles can be safely secured in any position according to DIN standards * Trailer hot-dip galvanized Load securing equipment also available from us: tensioning and lashing straps * Load bars * Safety vests * Transport boxes * Edge protectors * Airbags * Wheel chocks Gcodpfxsrwdr As Ab Tea * etc. Financing and leasing available We manufacture superstructures of any size and type for any chassis. Tarp, GRP sandwich, aluminum. Visit us at: Bodies - Complete vehicles - Trailers - Consultation - Financing Subject to errors and prior sale. No liability for printing or input errors.

Stanje: zelo dobro (rabljeno), KATALOGŠKA ŠTEVILKA 6114 TEHNIČNI PODATKI - Vstop lijaka za nalaganje 800x1000mm - Delovna širina rotorja 800mm - Motor črpalke 0,75kW - Glavni motor 15kW - Število nožev 21 kos - Dimenzije nožev 30x30mm - Sito 0,8x10mm Gcsdpfxognzd Ej Ab Tsa - Vlečna predal - Električni avtoobrat - Izpadna polža 2×1,1kW - Dimenzije d/š/v 2460x1800x2250mm - Teža 1660kg – Nemška proizvodnja – Avtoobrat – Vlečna predal – Neopremljen z barvo – Zelo dobro stanje – Rabljeni drobilnik Neto cena: 63900 PLN Neto cena: 15200 evrov odvisno od tečaja, 4,2 evra (Cene se lahko spremenijo ob večjih nihanjih)

Leto izdelave: 2025, Stanje: novo, BEFARD XP602 Vacuum Suction Cup for Glass Installation • Maximum load capacity: 600 kg • 8 suction cups • Dual-speed vacuum system • Vacuum release pilot • Battery-powered • Manual 360-degree rotation • Locks at each 90-degree increment • Fully adjustable for vertical and horizontal alignment Additional options: • HS spacer • Spare battery • Transport trolley Gedpoiauz Nofx Ab Tjca • Mesh box pallet Other models available: Grippers with load capacities of 300 kg, 450 kg, 800 kg, 900 kg, 1000 kg Available in your desired color

Leto izdelave: 2023, Stanje: novo, Stock machine Gcodpfxjhwdvce Ab Tsa Completely newly developed high-performance centrifuge. Based on our many years of manufacturing experience with the predecessor model of this centrifuge, we have implemented various improvements regarding maintenance costs, downtimes, and wear parts.

Leto izdelave: 2024, Stanje: novo, Funkcionalnost: popolnoma funkcionalen, The copper wire granulator can recycle scrap copper wire into separated copper and plastic. The processing capacity is 100–180 kg/h, and the dry mechanical shredding process causes no environmental pollution. For sale is the granulator, including a pre-shredder and a conveyor belt with magnet. Gsdpfx Aeu Tq S Heb Teca Design and Manufacturing 99.99% Outstanding Efficiency and Reliability, Advanced Technology: ● Airflow gravity sorting system for separating copper particles from insulation. ● Powerful vibrating separator to ensure clean separation of copper granulate from insulation by weight. ● Self-cleaning dust collection system to minimize maintenance time and eliminate dust. ● Compact design with a small footprint. ● 99.99% pure copper recovery rate ● High reliability ● High productivity ● Robust and versatile ● Long service life ● Cost-effective Technical Specifications Model: GRS 180KG Voltage: 380V Power: 8.7 kW Frequency: 50 Hz Processing capacity: 100-180 kg/h Dimensions: 80*137*204 cm Net weight: 518 kg