Stacionarna vijačna enota, vijačna postaja

WSM Automation Schraubstation

Stanje: dober (rabljeno), Bosch Turbo Scara SR8 robot + IQ200 upravljalnik Proizvajalec: Bosch Št. naročila: 3842999836 Serijska številka: 3810198 Hod*vreteno 400*25 PN tlak max. 8 bar Nosilnost max. 8 kg Teža 51 kg + upravljalnik IQ 200 Blsdpfxshbmwme Afnsd (Spremembe in napake v tehničnih podatkih so pridržane!) Območje nihanja glejte sliko Stanje artikla: rabljeno Poleg približno 50 paternosterjev so na voljo še številni drugi stroji, kot so stiskalnice, roboti, peči, industrijski sesalci itd. Delavniška oprema, delovne mize, vozički, orodja, viličarji in regali so na voljo v izobilju Skupno se razgrajuje in prodaja 24.000 m² proizvodnih površin Oglejte si tudi naše druge ponudbe. Po nakupu je treba znesek poravnati v 7 delovnih dneh. Dodatne nove in rabljene artikle najdete v naši trgovini! Cena mednarodne dostave na zahtevo!

Stanje: zelo dobro (rabljeno), Epson G10-854SR Robot Assembly Station Dispensing Station The assembly station is divided into the following sub-stations: 3.1 Dispensing Area, 3.2 Assembly Area Heatsink + Front Wall Bracket, and 3.3 Assembly Area Front. (KK = Heatsink, SW = Front Wall Bracket) St.3.1: Dispensing Area - A workpiece carrier (WT) with mounted chassis and PCB enters the dispensing area via the transfer belt. - It is stopped at the lift-positioning unit (HuPo), lifted off the belt and fixed in place. Bodpoibx S Nefx Afnold - Next, the x-y-z handling system moves the dispensing head to the specified location and starts the dispensing process. - After successful dispensing, the handling system moves into the park position and the WT is set back onto the belt. - The carrier is then conveyed to the Assembly Area Heatsink + Front Wall Bracket (provided there is no WT in the placement position). St.3.2: Assembly Area Heatsink + Front Wall Bracket - A WT moves from the dispensing area into the Assembly Area Heatsink + Front Wall Bracket via the transfer belt. - It is stopped at the lift-positioning unit (HuPo), lifted off the belt, and fixed in place; at the same time, the chassis side walls of the partially assembled unit are aligned. - Simultaneously, the heatsink tray and front wall tray are positioned. - A stack of 12 heatsink trays and a stack of 12 front wall bracket trays are manually placed onto the respective infeed belts outside the safety enclosure. - The two safety interlocks are opened and the loaded tray stacks move into the gripping position of each stacker. - The safety interlocks close again. - The corresponding grippers pick up the respective tray. - The tray is separated and transported upwards with the stacker z-axis to above the actual pick-up height. - To center and stabilize the tray, a centering support is pushed and positioned underneath each tray by the x-handling system. - With the stacker z-axis, each tray is set onto its corresponding centering support. - The trays are now ready for component removal. - Using the multi-gripper on the SCARA robot, the heatsink (KK) is gripped from the tray and placed in an intermediate alignment position (to compensate for pickup inaccuracies and ensure a repeatable gripping position for assembly). - The heatsink is scanned, picked up again, and if the scanner result is OK, it is assembled onto the WT. - If not OK, the heatsink is placed in an NOK box. - The SCARA robot multi-gripper then picks up the front wall bracket (SW) from the tray and places it in the alignment position. - The front wall bracket is picked up again and assembled onto the WT. - Proceed to Assembly Area Front. Technical Data Model: SCARA (4-axis robot) Payload: nominal 5 kg, max. 10 kg Horizontal reach: 850 mm Vertical reach: Axis 3: 420 mm Orientation range: J4: +/- 360° Horizontal repeatability: +/- 0.025 mm Vertical repeatability: J3: +/- 0.01 mm Orientation repeatability: J4: +/- 0.005° Max. operating range: Axis 1: +/- 152°, Axis 2: +/- 152.5°, Axis 3: 420 mm, Axis 4: +/- 360° Max. operating speed: J1,J2: +/- 11,000 mm/s, J3: +/- 2,350 mm/s, J4: +/- 2,400°/s Allowable moment of inertia: nom. 0.02 kg*m², max. 0.25 kg*m² User cabling electrical: 1x D-Sub 9 pin, 1x D-Sub 15 pin Z-Axis: Ø outer: 25 mm Press-in force: 250 N Weight: 48 kg Controller: EPSON RC180 Mounting type: ceiling IP Protection class: IP20 Power and signal cables: 3m Financing through our bank is also possible. Complete offer at komplett-konzept.leasingo.de

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 1998, Na voljo je stroj za kartoniranje lončkov Ammann. Tip lončka: 95, največji premer lončka: 95 mm, dimenzije kartona X/Y: 470 mm/330 mm, razporeditev: 3x6, zmogljivost pakiranja: cca. 15.000 lončkov/uro. Dimenzije stroja: cca. 2500 mm/2500 mm/2400 mm, teža: cca. 1700 kg. Stroj je bil leta 2008 predelan. Ogled na lokaciji je možen. Bjdpfsxuvpuex Afneld