Koordinatni merilni stroj

Renishaw InVia Raman Microscope Spectrometer

Stanje: rabljeno, TECHNICAL DATA - Number of spindles: 2 Bdedpfx Aoypxqrocbsi - Number of axes: 9 - Number of turret heads: 2 MAIN SPINDLE - Spindle drive power: 6.7 / 10.7 [kW] - Spindle speed: 8000 [rpm] - Max. bar diameter: 32 [mm] - Travel Z: 305 [mm] - Minimum C-axis resolution: 0.001 [degrees] SUB SPINDLE - Spindle drive power: 3.7 / 5.5 [kW] - Spindle speed: 6400 [rpm] - Max. bar diameter: 30 [mm] - Minimum C-axis resolution: 0.001 [degrees] - Travel X: 140 [mm] - Travel Z: 300 [mm] TURRET 1 - Number of positions: 10 - Number of live positions: 10 - Driven tool speed: 12,000 [rpm] - Driven tool power: 3.4 [kW] - Travel X/Z: 140/300 [mm] - Travel Y: -40/+25 [mm] TURRET 2 - Number of positions: 10 - Number of live positions: 10 - Driven tool speed: 12,000 [rpm] - Driven tool power: 3.4 [kW] - Travel X/Z: 140/320 [mm] - Travel Y: -25/+40 [mm] ELECTRICAL SUPPLY - Total power: 28 [kW] WEIGHT AND DIMENSIONS - Required floor space: 3870 x 1670 [mm] - Machine height: 2500 [mm] - Machine weight: 6000 [kg] OPERATING HOURS - Power-on hours: 23240 [h] - Operating hours: 19500 [h] ACCESSORIES - Control system: Traub TX 8i-p - 3-colour status lamp - Coolant tank: 500 [l] * with high-pressure pump: 3, 8, 20 [bar] * with paper filter - Chip conveyor - Workpiece removal - Parts conveyor belt - Bar feeder preparation

Stanje: rabljeno, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of Manufacture: 2007 Rolling Force: max. 24 tons Tool Diameter: max. 270 mm Roll Spindle Diameter: 69.85 mm Tool Bore Diameter: 70 mm (nominal diameter) Mounting Length, Tool Length: max. 180 mm Workpiece Diameter: max. 50 mm Hydraulic Motor Power: 3 kW Roll Drive Motor Power: approx. 5.5 kW Mains Connection: 400 Volt, 50 Hz, 10 kW Bsdouz If Nepfx Acbjdi - Pivoting roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gear shift - Hydraulic system integrated in machine frame - Operating manual with electrical diagram Space requirements (L x W x H): 2000 x 1450 x 190 mm Weight: approx. 3 tons Very good condition Plunge rolling: The thread rolling dies, with the same pitch as the workpiece, form the thread by pressing into the workpiece up to the nominal diameter. The thread length is at most as long as the width of the rolling dies. Through-feed rolling: Used when the thread length exceeds the width of the rolling dies. Through-feed dies have three functional zones – lead-in, calibration, and lead-out. Knurling Rolls: These rolls have no pitch and are swiveled at the pitch angle of the profile to be rolled. Pitch Rolls: Pitch rolls have a profile with a pitch, differing from knurling rolls. The sum of the pitch angle and swivel angle determines the pitch angle in the finished workpiece.

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2025, obratovalne ure: 10 h, Funkcionalnost: popolnoma funkcionalen, merilno območje os X: 200 mm, merilno območje osi Y: 200 mm, merilno območje os Z: 200 mm, trajanje garancije: 12 meseci, potovalna razdalja osi X: 200 mm, pomik osi Y: 200 mm, pomik po osi Z: 200 mm, vhodna napetost: 230 V, dolžina podajanja os X: 200 mm, dolžina pomika po osi Y: 200 mm, dolžina podajanja os Z: 200 mm, Oprema: Na voljo je tipska ploščica, dokumentacija / priročnik, osvetlitev, Completely overhauled multisensor measuring device Mahr MS 222 (optical measuring instrument) LIKE NEW, including acceptance certificate prior to delivery and free shipping within Germany* Factory-refurbished premium multisensor measuring center with warranty and guarantee, rebuilt in 2025. INCLUDES latest software update, 18 months of free software update service, free lifetime software hotline and user support. Delivery with factory service or via shipping company, worldwide delivery possible! Online or on-site demonstrations with customer parts as well as application-specific consulting provided by accredited Profitech inspection laboratories during project planning. Bjdpfx Acjglp Nqebjdi Complete service available upon request: – Delivery, installation, commissioning, norm-compliant accuracy verification, certification, and comprehensive acceptance documentation. Customized training programs also available as online courses. Rental, hire-purchase, or financing available directly via Profitech, with no bank required. Measuring device can be configured individually to customer needs. Measuring range: 200 x 200 x 200 mm Load capacity (glass plate): 10kg Scale resolution: 0.1μm Max. traverse speed: 150mm/s Dimensions: 900 x 750 x 950mm Machine weight: 170kg Control cabinet weight: 90kg Length measurement uncertainty: According to VDI/VDE 2617-6 E2 (X,Y) = (3.2 + L/125) μm Optional extension: Renishaw probe system (TP20, TP200, SP25) available on request Retrofit 2025 Including PC and software Maximum traverse speed: 150mm/s Dimensions: 900 x 750 x 950 Weight: approx. 90 kg Sample image by manufacturer *Commissioning, on-site calibration, and training are not included

Stanje: dober (rabljeno), Leto izdelave: 2004, Funkcionalnost: popolnoma funkcionalen, Oprema: vrtilna hitrost brezstopenjsko nastavljiva, Citizen C16-VII CNC Swiss Type Lathe Year of manufacture: 2004 Control: Mitsubishi Meldas 635 Max. machining diameter: 16 mm C-axis: main and sub spindle 5 controlled servo axes: X1/Z1/Y1/X2/Z3 4 driven tools on the vertical holder C-axis: main and sub spindle Including accessories: LNS Express 220 bar feeder, conversion kit for 16 mm and 10 mm Donaldson Torit extraction system Chip conveyor Bdedsv Rhd Hspfx Acbsi - Immediately available -

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2017, obratovalne ure: 24.140 h, skupna masa: 10.000 kg, proizvajalec krmilnikov: FANUC, model krmilnika: 31i-NT-SmartX, število osi: 9, This 9-axis Nakamura NTJ100 turning-milling center was manufactured in 2017. It features a bar capacity of up to 65 mm and two spindles with maximum speeds of 4,500 and 5,000 rpm, respectively. The machine is equipped with a Samsys bar feeder, an Absolent extraction system, and numerous automated features such as through-spindle coolant supply, parts catcher, and automatic tool setting devices. Take advantage of this opportunity to purchase the Nakamura NTJ100 turning-milling center. Contact us for further information about this machine. • Increased bar capacity: 65 mm left, 51 mm right • Workpiece measurement: han-bei probe for automatic workpiece measurement (infrared or radio) for left and right spindle • Left and right with automatic swing-out function and 2x 4 measuring directions for rapid and precise tool setting via NC function • Operating hours: 43,399h • Coolant system: through-spindle coolant (CTS); coolant level float switch for machine stop at low level; additional through-spindle coolant flushing (left and right) • Bar capacity: Ø 51 mm • Type A parts catcher with collection tray, max. Ø 65 x 150 mm, 3.0 kg, spindle side, left, with plastic liner • Chuck air blow device for left spindle • Automatic power-off • Preparation for oil mist extraction unit with Ø 150 mm connection stub Bdedpfxox D Iuzo Acbei • Robot/automation preparation: pneumatic flap for robot handling at the top of the door, opening approx. 400 x 400 mm • Handwheel for manual travel of defined contours • Data server with 1 GB ATA memory card • Interface for KNOLL system • Triple signal light The Samsys bar feeder with a 1.5 m bar loading capacity has the following dimensions: length: 225 cm + 43 cm intermediate guide, width: 120 cm (including loading ramp and control panel), height: 145 cm or 180 cm with open flap. The machine was primarily used for processing aluminum (95%). Additional equipment: • Samsys bar feeder including extension • Absolent extraction unit • Hinge belt swarf conveyor with interface, interval time control, and alarm analysis

Leto izdelave: 2005, stanje: pripravljen za uporabo (rabljen), - RABLJEN - 6-OSNI AVTOMATSKI STRUŽNI STROJ S POMIČNO GLAVO IN DOVAJALNIKOM PALIC MAKSIMALNA DOLŽINA OBDELOVANJA: 320 mm MAKSIMALNI PREMER OBDELOVANJA: 32 mm VRETENO: 200–8000 min⁻¹; 3,7–7,5 kW PROTIVRETENO: 200–7000 min⁻¹; 1,5–2,7 kW POMIK OSI X1: 108 mm POMIK OSI X2: 228 mm POMIK OSI Y1: 275 mm POMIK OSI Z1: 325 mm POMIK OSI Z2: 130 mm POMIK OSI Z3: 410 mm Bdsdpfx Acsvthv Ijboi HITRI POMIKI OSI X-Y-Z: 20 m/min REVOLVERSKA GLAVA Z GNANIMI ORODJI: 8 POZICIJ; 200–5000 min⁻¹ KRMILNA ENOTA: CINCOM SYSTEM M6D DOVAJALNIK PALIC: IEMCA Mod. BOSS 332 EVOLUTION TEŽA: 2850 kg DODATNA OPREMA: LOVILEC OBDELOVANCEV

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2008, Funkcionalnost: nepreverjeno, številka stroja/vozila: R14507, Year 2008 with Fanuc 18i-TB With LNS Tryton 107 Country of manufacture: JP Voltage: 200V 3ph 50/60Hz Dimensions: 141x56x140 cm Net machine weight: 950 kg TECHNICAL SPECIFICATIONS (standard) Number of axes: 6 Number of spindles: 2 Main spindle Max bar diameter: Ø 7 mm Max machining length: 40 mm Stroke: 40 mm Spindle speed: 16,000 rpm Spindle power: 1.1 kW C-axis indexing accuracy: 0.0001° Sub-spindle Max bar diameter: 7 mm Spindle speed: 10,000 rpm Power: 0.5 kW C-axis indexing accuracy: 1° Tool post 1 Number of positions: 5 Powered positions: 2 Rotating tool speed: 8,000 rpm Bjdpfeya Aq Rox Acbsdi Tool post 2 Number of positions: 3 End tool holder Number of positions: 3 Sub-operation Number of positions: 3 All technical details are provided without guarantee, subject to errors or omissions.

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2014, obratovalne ure: 51.488 h, Ta švicarski CNC stružnica Citizen CINCOM A32-VII CL je bila izdelana leta 2014. Opremljena je z glavnim vretenom s kapaciteto 32 mm, protivretenom in največjo dolžino struženja 3000 mm. Ponaša se s hitrim sistemom CHIDOMI, ki omogoča hkratno gibanje po vseh oseh in ponuja podajalno hitrost do 9.000 mm/min. Razmislite o priložnosti za nakup te švicarske stružnice Citizen CINCOM A32-VII CL. Kontaktirajte nas za dodatne informacije o stroju. Bdsdpox D Nhpsfx Acboi Vrste uporabe: Struženje

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2023, Na voljo je CNC portálna koordinatna merilna naprava Mitutoyo. Pomik osi X/Y/Z: 1200mm/2000mm/1000mm, merilni volumen: 2,4m³, maks. teža obdelovanca: 2500kg, maks. višina obdelovanca: 1000mm, merilna tipala: Renishaw, število pozicij tipal: 20, merilna natančnost: 2,3+/-0,3/100µm, maks. hitrost pomika: 693mm/s. Dimenzije stroja X/Y/Z: pribl. 3400mm/2200mm/3600mm, teža: pribl. 6150kg, krmiljenje: Mcosmos-3 V4.3. Dokumentacija na voljo. Ogled na lokaciji možen. Bedpfx Aezhnrbjcbedi

Leto izdelave: 2025, stanje: novo, X-ray inspection system for medium-sized packs and pouches. Suitable for the detection of foreign objects such as metal, glass, stone, plastic, etc., in food or non-food products. Bodov Nm Injpfx Acbedi Specifications: Conveyor belt width: 410 mm; Detection sensitivity: Pb from Ø 0.2 mm, Fe from Ø 0.28 mm, SUS from Ø 0.28 mm, non-metallic (e.g. stone, glass) from Ø 1.2 mm; X-ray output: 80 kVp, 1.25 mA; Detector resolution: 0.4 mm; X-ray emission: < 1 µSv/h; Conveyor belt height: 850 ± 30 mm; Conveyor belt speed (product-dependent): 10–100 m/min; User interface: 15" touchscreen; Software: intellisens®X-ray; Operating temperature: 5–35 °C; Ejection system: optionally available as required; Power supply: 220VAC, 50/60Hz; System dimensions: L900 x W920 x H1825 mm; Weight: 350 kg. Please note that our new prices are often below conventional used prices. Feel free to send us an enquiry and describe your specific packaging application. We typically have 30–50 different new machines available ex stock for immediate delivery. For custom-built equipment, we offer very short lead times, starting from approximately 3 weeks. All machines are supplied with a full warranty.