Generatorji Električne Energije nakup rabljenega (1.894)

Leto izdelave: 2016, stanje: pripravljen za uporabo (rabljen), Two identical machines are available, Power 1/2: 5000/9000 VA, Speed: 1800/3150 rpm, Length: 700 mm, Width: 440 mm, Height: 580 mm, Weight: 126 kg, including documentation. The generators are unused. Fodpfjrn Ta Hsx Aprjpk

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2016, Fuel: Natural gas (NG), Engine: HMG, Combined heat and power unit (CHP) for space heating: Yes, Condensing boiler: No, Auxiliary heater: No, Low-temperature boiler: No, B11 boiler: No, Combi-unit: No, Rated heat input P: 88 kW, Annual efficiency of space heating system η: 136%, Energy efficiency class: A++, usable heat output at rated heat input with auxiliary heater switched off/on: 87.9 kW, thermal efficiency at rated heat input with auxiliary heater switched off/on: 57.5%, electrical efficiency at CHP space heater output with auxiliary heater switched off/on: 33.5%, auxiliary power consumption at full / partial load el: 1.132 kW, standby power consumption P SB: 0.06 kW, standby heat loss P stby: 0.442 kW, annual energy consumption Q HE: 1345 kWh, indoor sound power level L WA: 72 dB, operating hours: 42,892 h. Water has been detected in the oil circuit; the unit displays a fault with the oil even though sufficient oil is present. Furthermore, the device shuts down with the message 'Engine too hot.' The control system was overhauled by the manufacturer in 2024; maintenance intervals for oil changes, spark plugs, valves, etc. have been carried out regularly and documented. Fpjdpfxjxc Ni Rj Aprsk

Stanje: pripravljen za uporabo (rabljen), A combined heat and power plant (CHP), consisting of three diesel generators installed in containers, is available. 1) Engine: MAN 12-cylinder turbo, type: D 2842 LE 20. Generator: Krauter, type: D-SYN-GEN, kVA: 400, kW: 360, A: 577, Hz: 50, speed: 1500 rpm. Includes DELF synchronisation, hot water outlet, table cooler, pre-heating system, and oil change system. 2) Engine: MAN 12-cylinder turbo, type: D 2842 LE 20. Generator: Leroy-Somer, type: LSA K 475 L10, kVA: 375, kW: 300, A: 400, Hz: 50, speed: 1500 rpm. Includes DELF synchronisation, hot water outlet, table cooler, pre-heating system, and oil change system. 3) Engine: Daimler Benz 8-cylinder turbo, type: AGV 12. Generator: Krauter, type: D-SYN-GEN, kVA: 350, kW: 230, A: 400, Hz: 50, speed: 1500 rpm. The combined heat and power plant has a total output of approximately 1100 kVA. Includes table coolers, V2A heat exchangers, containers, and control cabinets. All generators are containerised for ease of transport. Fedpfstwqzrsx Apropk

Stanje: rabljeno, Leto izdelave: 2008, Na prodajo ponujamo MTU kogeneracijsko enoto z nazivno električno močjo 1,2 MW. Tehnični podatki: Proizvajalec: MTU Motor: MTU 12V4000L62 Generator: Stamford Leto izdelave: 2008 (generalno obnovljen leta 2015) Delovnih ur: 63.000 Fpedpfx Apjxcwlaorok Vključno z elektro omarami Vključno z miznim hladilnikom

Stanje: rabljeno, moč: 24 kW (32,63 KM), barva: rumena, Leto izdelave: 1996, obratovalne ure: 11.776 h, GENERATORSKI SKLOP CATERPILLAR GEP30 OLYMPIAN...DIZELSKI SKLOP Z MOČJO 30 KVA...DELUJE BREZHIBNO...ZAŽENE SE IN DELUJE... Fsdei Uz Iqjpfx Aprspk

Leto izdelave: 2025, stanje: novo, Funkcionalnost: popolnoma funkcionalen, Različne velikosti, več na zalogi v Švici, vsi novi, takoj dobavljivi! 20kVA, 400V, 4 valji, diesel --> 6.000€ 50kVA, 400V, 4 valji, diesel --> 12.500€ Fpodotd Nzmepfx Aprjk Popust pri nakupu več strojev!

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2025, vrsta aktuacije: električni, delovna širina: 2.000 mm, kot rezanja (min.): 1 °, frekvenca hodov (min.): 40 obr/min, najv. debelina pločevine: 2 mm, maks. debelina aluminijaste pločevine: 2 mm, moč: 2,2 kW (2,99 KM), skupna masa: 500 kg, skupna dolžina: 2.280 mm, skupna širina: 550 mm, skupna višina: 1.850 mm, trajanje garancije: 24 meseci, Oprema: nujno zaustavitev, debelina jekla za rezanje Fpsdsymc Nyepfx Aprek

Stanje: rabljeno, Funkcionalnost: omejena funkcionalnost, Ferwood Code: RU0008196 - Manufacturer Code: MDR60A0750-503-00 - Condition: Used - Functionality: Limited functionality - Compatible Machine: CNC - IMA LOADING/UNLOADING - BARGSTEDT - MEINERT - If interested, we offer refurbishment services; please contact us. Fedpfx Ajv Hgcyjprspk

Stanje: rabljeno, Funkcionalnost: omejena funkcionalnost, Ferwood Code: RU0008195 - Manufacturer Code: MDR60A0370-503-00 - Condition: Used - Functionality: Limited functionality - Compatible Machine: CNC - IMA LOADING/UNLOADING - BARGSTEDT - MEINERT - If interested, we offer a refurbishment service; please contact us. Fjdpfxev Hgcgo Aprspk

Stanje: novo, Leto izdelave: 2026, Generator toplega zraka, peč za ogrevanje z vročim zrakom, delavniška peč, ogrevanje za hale, model F28, F55CV, F85CV, F120CV, F240CV. NOVI stroji. Takojšnja dostava. Za stroje, ki so na voljo za takojšnjo dostavo, vam ponujamo cenik za leto 2024 z 35-odstotnim popustom. Akcijska ponudba poletje 2026. Stroji uporabljajo les kot gorivo. CE-uredba: DA. Izjava o skladnosti z direktivami ES: DA. Navodila za uporabo: DA. Fpedpfx Aeh U A Uaoprsk Indikativna površina, ki jo lahko ogreje model F28: m2 100/150. Približna površina, ki jo lahko ogreje model F55CV: m2 300/350. Približna površina, ki jo lahko ogreje model F85CV: m2 450/500. Približna površina, ki jo lahko ogreje model F120CV: m2 600/700. Približna površina, ki jo lahko ogreje model F240CV: m2 1.000.

Stanje: dober (rabljeno), Leto izdelave: 2006, obratovalne ure: 535 h, vrsta goriva: električni, JLG 2646ES dvižna platforma / mobilna platforma / škarjasta platforma, višina delovne platforme 10 m, električna, leto izdelave 2006. Video lahko pošljemo preko WhatsAppa. Nenehno imamo na zalogi, glejte spletno stran. Cene so določene za Nuland. Podjetje Van de Wert Trading B.V. ima različno ponudbo strojev, tovornih vozil, priklopnikov in dodatne opreme. Vse naše dobave so po tržnih cenah, v stanju »kot je«, brez garancij. (glejte naše splošne pogoje) Za ogled in/ali preizkusno vožnjo lahko brez obveznosti dogovorite termin. Pokličite predhodno, saj nismo vedno prisotni. Fpedpfx Apezpyvuerjk Van de Wert Trading B.V. Bedrijfsstraat 3 5391 LR Nuland

Stanje: skoraj kot novo (rabljeno), obratovalne ure: 250 h, SHI-Machines Type: BlueBox Practically unused with only 250 operating hours! Technical Data: Power output: 120 kW Fsdpfxey Tg R No Aprepk Torque: up to 470 Nm Speed: up to 6,000 rpm Operation: Four-quadrant operation Safety package: Bulletproof cover & data filter for "Go" signal line Dimensions: approx. 2800 × 1600 × 1300 mm Accessories etc.: 1 clutch 120 – steel, incl. adapter Clutch size: 100 Max. speed: 7,300 RPM Max. torque: 1,000 Nm 1x adapter 1x clutch steel size 100 1x adapter 2 ø40 1x adapter 2 ø50 1x adapter 2 ø60 1x clamping device ø40 1x clamping device ø50 1x clamping device ø60 Adapter installation tool Clutch 120 – CFRP, incl. adapter max. speed: 8,500 RPM max. torque: 720 Nm Adapter installation tool CISPR 25 test bench made of wood on casters for EMV-BlueBox 120 Size 2500 x 1000 x 900 mm Load capacity up to max. 500 kg, incl. 2 mm hot-dip galvanized ground plane Payload: up to 1,400 kg Weight: approx. 2,500 kg Operating voltage 400 V, 250 A Control voltage 24 V Condition: used Scope of delivery: (See picture) (Subject to changes and errors in the technical data, all details are without guarantee!) We will be happy to answer further questions by phone.

Stanje: rabljeno, Forklift motor, electric motor, DC motor, traction motor, drive motor - Voltage: 75 V - Power output: 6.3 kW - Speed: 1,400 rpm - Dimensions: 510 x 320 x H280 mm - Weight: 76 kg Fedpfx Aedvlu Aeprjpk

Stanje: rabljeno, Gear motor, electric motor - Gear motor for: Electric forklift Steinbock LE 15-60 MK IV A-1 - Connection: 24 Volt - Dimensions: 400/300/H160 mm Fjdpfjdwhuuex Aprjpk - Weight: 25 kg

Stanje: dober (rabljeno), - Tester for electrical devices Fpedpfx Apeb A Ivzorjk - Each equipped with an isolation transformer - Quantity: 7 units available - Price: per piece

Stanje: dober (rabljeno), Linearno ležišče, linearna tirnica, linearno vodilo, valjčno vodilo, vodilni voziček, vodilna tirnica, valjčni voziček, električni drsnik, linearni drsnik -Proizvajalec: Afag, električni linearni drsnik -Tip: ES30-400 Fsdsxw Ubbepfx Aprjpk -Hod: 400 mm -Gred: Ø 20 mm -Dimenzije: 630/60/120 mm -Teža: 6,6 kg

Stanje: dober (rabljeno), Linearno ležišče, linearna tirnica, linearno vodilo, valjčno vodilno tirnico, vodilni voziček, vodilna tirnica, valjčni voziček, električni linearni voziček, linearni voziček -Proizvajalec: Afag, električni linearni voziček -Tip: ES30-300 -Hod: 300 mm -Gred: Ø 20 mm Fpsdpfxjxw Ub Ue Aprok -Mere: 525/60/120 mm -Teža: 5,8 kg

Stanje: dober (rabljeno), Forklift motor with gearbox, electric motor, DC motor, drive motor, traction motor - Voltage: 23 V - Power: 3 kW - Speed: 1705 rpm Fedpfx Apsdp Npisrjpk - Traction motor for: Steinbock forklift - Dimensions: 375/230/H200 mm - Weight: 25 kg

Stanje: rabljeno, Clamping motor for wedge bar chuck, three-jaw chuck, three-jaw power chuck, power chuck, hydraulic power chuck, hydraulic power chuck motor, electric clamping device -Make: Berg Spanntechnik, Clamping Motor Type FSP 140 U -Shaft: M22 x 1.5 Fpjdpfx Apod S Hqdorok -Dimensions: Ø 140/490 mm -Weight: 24.5 kg

Stanje: novo, Proizvajalec: INA Schaeffler Stanje: Novo, embalaža je bila odprta samo za namen fotografiranja Tip: Sistem za prenos energije / nosilec kablov Model: Mekokab 150/180/325-WH-AL-B Serija izdelka: Mekokab Izvedba: Energetska veriga oz. sistem za vodenje kablov Material: Aluminijasta izvedba Področje uporabe: Orodni stroji, avtomatizacijske naprave, manipulacijska tehnika in industrijske gibljive osi Fpodjzcw I Nspfx Aprok Uporaba: Vodenje in zaščita energetskih, krmilnih in podatkovnih kablov pri gibljivih aplikacijah Skupina proizvajalcev: Schaeffler Industrial Automation Razpoložljiva količina: 2 kosa

Stanje: rabljeno, Three-phase power meter, current, voltage and power measurement, long-term measurement, energy measurement 3-phase power measurement device, ammeter, voltmeter, digital measuring instrument, active power, apparent power, reactive power BEHA TYPE UNITEST Power Analyzer 93555 For measuring voltage, current, active power, apparent power, reactive power, power factor, phase angle, frequency measurement, phase sequence detection, energy measurement, harmonic measurement Display: LC multifunction display with backlighting Refresh rate: approx. 2 sec. Datalogger: 512 kb non-volatile memory (max. 21,000 readings, max. 10 measurement series) Sampling rate: 5s, 30s, 1 min, 2 min (adjustable) Data transfer: via optically isolated RS232 interface Manual reading storage: max. 99 measurements Overvoltage category: CAT III 600 V Power supply: 8 pcs 1.5V batteries (AA) or plug-in power supply 230VAC / 12VDC (batteries not included) Voltage measurement: 3 input channels with common reference point "N" Measuring range: 0 - 600 V AC (RMS) Display range: 0 - 999.9 V AC (RMS) Resolution: 0.1 V Mains frequency: 50 Hz Current measurement: Measuring range input I1, I2, I3: 3 - 999.9 A Input I4: 3 - 250 A Display range: 0 - 999.9 A Fedex A Imzjpfx Apropk Resolution: 0.1 A Jaw opening: 40 mm Active power: Selectable display of the active power of a single input or of the total value Display range: 0 - 999.9 kW Resolution: 0.1 kW Apparent power: Calculated from the RMS values of voltage and current Display range: 0 - 999.9 kVA Resolution: 0.1 kVA Frequency measurement: Measuring range: 45...80 Hz Resolution: 0.1 Hz Accessories: - Carrying case - Operating manual - 4 current clamps - 4 measuring leads with crocodile clips - RS232 adapter cable - Plug-in power supply 230VAC / 12VDC Overall dimensions (W x H x D): 370 x 270 x 170 mm Total weight: 3 kg Device tested, fully functional. The housings of 2 current clamps are damaged and the battery compartment is slightly oxidized, see pictures.

Stanje: novo, Pressure: 150 Bending length: 3050 mm Frame gap: 3050 mm Installation height: 590 mm Max. stroke length: 300 mm Dimensions (LxWxH): 4740x2000x2680 mm Weight approx.: 9500 kg Motor power: 22 kW CNC crowning via control: yes CNC Servo Electric Press Brake KKI Model: REVOLUTION DDM-15030 Servo-motorized Press Brake REVOLUTION Servo-electric press brakes contain no hydraulic system and, due to their flexibility and reliability, represent the technology of tomorrow. The higher speed and precision of this new machine generation offers improved efficiency, ergonomic features, and more environmentally friendly production technology. As the first manufacturer of servo-electric press brakes with various models and capacities, Dener is a pioneer of this technology, bringing extensive experience and quality. Standard Equipment: KK-Industries holds the general agency of the DENER group. We have configured a high-quality model for Europe. The CNC servo electric press brake KK-Industries, made by DENER, includes: Technological Advantages, Model REVOLUTION DDM: The CNC servo electric press brake is characterized by high precision, accuracy, and versatile application possibilities. - 100% electric, 0% hydraulic oil - Up to 50% reduced energy consumption compared to conventional hydraulic press brakes - High efficiency and accuracy - High bending speed and significantly quieter - Usable full frame length - Lower maintenance costs - Environmentally friendly - User-friendly control panel - Automatic calculation of bending steps directly from STEP or DXF files - Up to 35% faster than hydraulic press brakes Standard Equipment Includes: 3D color graphics controller DELEM 66T with 17-inch touchscreen Y1, Y2, X, and R axes controlled by CNC CNC crowning via 3D control X-axis 500 mm, R-axis stroke 150 mm (for 1.5 m and 2 m models) X-axis 750 mm, R-axis stroke 250 mm (on other press brakes) We make no compromise on tooling, equipping the KKI REVOLUTION CNC servo electric press brake with quality tools from EUROSTAMP Italy. Segmented gooseneck upper tool 4-V die block 60x60 (V = 16, 22, 35 and 50 mm) Back gauge with servo motors on linear guide and ballscrew Of course, a machine is only as good as its service. Therefore, we focus on highly qualified staff with long-standing experience in CNC sheet metal processing. Laser safety device on the upper beam CE safety equipment Fjdpfxod Etf Eo Apropk Operating manuals in GERMAN and ENGLISH Options: Additional controlled axes for backgauge: X1, X2, R, Z1, Z2, Delta X ATF type 6-axis backgauge, X1, X2 - R type backgauge X-Prime type backgauge Hydraulic upper and lower tool clamping for WILA tools CNC 3D touchscreen DELEM DA-69T control KK-Industries GmbH

Stanje: novo, Pressure: 20 Bending length: 900 mm Frame width: 900 mm Installation height: 325 mm Stroke length (max.): 150 mm Dimensions (LxWxH): 1760 x 1280 x 2190 mm Approx. weight: 1950 kg Motor power: 3.8 kW Electric ball screw CNC press brake KK Industries Model REVOLUTION B-Servo 900 mm x 20 t Standard equipment: KK-Industries is the general representative of the DENER group. We have assembled a high-quality model for Europe. The CNC Servo Electric Press Brake, KK-Industries made by DENER: Technological Advantages: Model REVOLUTION B-Servo 900 mm 20 t - High speeds with ball screw drive - The CNC servo electric press brake stands out for its high precision, accuracy, and versatile application possibilities - 100% electric, 0% hydraulic oil - Up to 40% lower energy consumption compared to conventional hydraulic press brakes - High efficiency and accuracy - High bending speed and significantly quieter operation - Reduced maintenance costs - Environmentally friendly - User-friendly control panel - Automatic calculation of bending steps directly from STEP or DXF files - Up to 35% faster than hydraulic press brakes Technical Specifications Bending Length (B): 900 mm Bending Capacity (Pressing force): 20 tons Maximum Stroke: 150 mm Daylight Opening (Q): 325 mm Approaching Speed: 150 mm/s Bending Speed: 20 mm/s Return Speed: 150 mm/s Power: 3.8 kW Weight: 1950 kg Overall Length (A): 1760 mm Fpedpfx Asd H Hh Deprok Width (C): 1280 mm Height (D): 2190 mm KK-Industries GmbH There's something for everyone!

Stanje: novo, Pressure: 80 Bending length: 2550 mm Distance between uprights: 2550 mm Installation height: 590 mm Max. stroke length: 300 mm Dimensions (LxWxH): 3680 x 1960 x 2500 mm Approx. weight: 6100 kg Motor power: 11 kW CNC Servo Electric Press Brake KKI Model: REVOLUTION DDM-8025 Servo Motorized Press Brake REVOLUTION Servo-electric press brakes contain no hydraulic system and, thanks to their flexibility and reliability, represent the technology of tomorrow. The increased speed and precision of this new generation of machines provide higher efficiency, ergonomic features, and a more environmentally friendly production technology. As the first manufacturer of servo-electric press brakes with various models and tonnages, Dener is a pioneer of this technology, offering extensive experience and high quality. Standard equipment: KK-Industries is the general representative of the DENER group. We have assembled a high-quality model specifically for Europe. The CNC Servo Electric Press Brake by KK-Industries, made by DENER, offers technological advantages: - 100% electric, 0% hydraulic oil - Up to 50% less energy consumption compared to conventional hydraulic press brakes - High efficiency and precision - High bending speed and significantly quieter - Full length between the frames is usable - Lower maintenance costs - Environmentally friendly - User-friendly control panel - Automatic calculation of bending sequences directly from STEP or DXF files - Up to 35% faster than hydraulic press brakes Standard equipment includes: - 3D color graphics control Delem 66T with 17" touch screen - Y1, Y2, X, and R axes CNC controlled via the controller - CNC crowning via the 3D controller - X-axis 500 mm, R-axis stroke 150 mm for 1.5 m and 2 m models - X-axis 750 mm, R-axis stroke 250 mm on all other press brakes - No compromises on the upper tool and die: CNC Servo Electric Press Brake KKI REVOLUTION equipped with high-quality tools from EUROSTAMP Italy - Segmented gooseneck upper tool - 4-V die block 60x60 mm (V = 16, 22, 35, and 50 mm) - Backgauge controlled by servo motors on linear guides and ball screws - As with any machine, service quality is pivotal; for this reason, we focus on highly qualified staff with extensive experience in CNC sheet metal processing - Laser safety device on the upper beam - CE safety equipment Fpedpfx Apod Etfworjk - Operating manual in GERMAN and ENGLISH Options: - Additional controlled backgauge axes: X1, X2, R, Z1, Z2, Delta X - ATF Type 6-axis backgauge, X1, X2 - R Type backgauge - X-Prime Type backgauge - Hydraulic upper and lower tool clamping for tools - CNC 3D touchscreen controller DELEM DA-69T We recommend the following options: - Manual crowning € 2,329 - CNC crowning € 4,658 KK-Industries GmbH

Stanje: novo, Pressure: 40 Bending length: 1300 mm Frame gap: 1300 mm Installation height: 375 mm Stroke length (max.): 150 mm Dimensions (LxWxH): 1880 x 2435 x 2320 mm Weight approx.: 3400 kg Motor power: 2 x 3.8 kW electric ball screw CNC press brake KKI Model REVOLUTION B-Servo 1550 mm x 40 t Standard equipment: KK-Industries is the general representative of the DENER Group. We have assembled a high-quality model for Europe. The CNC servo-electric press brake from KK-Industries, made by DENER, offers technological advantages: Model REVOLUTION B-Servo 1550 mm 40 t High speeds with ball screw drive The CNC servo-electric press brake stands out for its high precision, accuracy and versatile applications - 100% electric, 0% hydraulic oil - Up to 40% lower energy consumption compared to conventional hydraulic press brakes - High efficiency and accuracy - High bending speed and significantly quieter operation - Reduced maintenance costs - Environmentally friendly - User-friendly control panel - Automatic calculation of bending steps directly from STEP or DXF files - Up to 35% faster than hydraulic press brakes Technical Specifications Bending Length 1550 mm Bending Capacity (Press force) 40 tons Maximum Stroke 150 mm Daylight Opening (Installation height) 375 mm Approaching Speed 150 mm/s Bending Speed 20 mm/s Return Speed 150 mm/s Power 2 x 3.8 kW Weight 3400 kg Overall Length (A) 1880 mm Width (C) 2435 mm Height (D) 2320 mm KK-Industries GmbH There's something for everyone! Fpsdpfxed H Hh He Aprek