Enojni vijačni iztiskalnik 25/25 LD

Stanje: generalkompletno obnovljen (rabljeno), Leto izdelave: 2018, mobile hammer mill Mobil Flex 1000 with drum magnet and discharge conveyor Drive: 250 kW electric 4 hydraulic supports for lifting the machine for transport total weight: 33,000 kg rotor weight: 3,000 kg output: up to 11 t/h (depending on material size, screen size, parameter settings) with soundproof enclosure dimensions: 11,750 x 2,500 x 4,380 mm number of hammers: 24 pcs. weight per hammer: 22 kg Fgodpfxoph Uy To Aa Hok unit is being overhauled

Stanje: rabljeno, Edge banding machine - Sumbel Perkeo Year of manufacture: 2014 - Serial No.: 40050 Max. working width: 60 mm Cold glue application system Fgsdewgdw Topfx Aa Hsk --like new condition-- Online video inspection possible via WhatsApp, MS Zoom, or Telegram In stock in Emskirchen/Nuremberg - Immediately available - Test run possible

Stanje: dober (rabljeno), Multivac termoformirni stroj je trenutno konfiguriran za proizvodnjo hotelskih porcij marmelade, 14 g in 20 g. 32 porcij na cikel. Stroj je primeren tudi za izdelavo ledenih kock, porcijskih embalaž za omake, kečap, jušne osnove ipd. Po dogovoru je mogoče dobaviti tudi celotno linijo z M&P 32-glavim polnilcem in končno linijsko ovijalnico pladnjev (za doplačilo). Fgodpstp N Ddsfx Aa Hsk

Stanje: novo, Leto izdelave: 2024, Saw Saw blade speed: 3000 / 4000 / 5000 RPM Saw blade diameter and bore: 300 – 400 mm, 30 mm Saw blade tilting: 90° – 45° Cutting depth at 90° / 45°: 125 mm / 90 mm Cutting width with parallel fence, version Z400 M, Z400 EL: 1350 mm (option 1000 / 1525 mm) Cutting width with parallel fence, version Z400 X1, Z400 X3: 1250 mm (option 1500 mm) Cutting length: 3500 mm (option 2500 mm / 4100 mm) Cast iron table dimensions: 985 mm x 710 mm Sliding table dimensions: 3200 mm (option 2200 mm / 3800 mm) x 420 mm Cross table dimensions: 1420 mm x 650 mm Length of swiveling cross fence: 2295 mm (telescopic extension up to 3000 mm) Scoring unit Scoring saw blade diameter and bore: 120 mm, 20 mm Cutting depth with 120 mm scoring blade: 3.5 mm Scoring blade rotational speed: 8200 RPM Scoring saw motor power: 1.3 kW / 2 HP (S6) Weight: 850 kg (Z400 – 3200) – 1080 kg (Z400 X3 – 3800) Fsdoglfv Sjpfx Aa Hjgk Power supply: 400 V 3-phase (option 230 V 3-phase) Motor power (3-phase): 7 kW / 9.5 HP (S6), option 9.2 kW / 14 HP (S6)

Leto izdelave: 2022, Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, We are offering for sale an Instron tensile and compression testing machine in excellent condition. Instron 34TM-50 tabletop model with 3 load cells and a wide range of accessories (see pictures). Configuration: E1-F1-G1 50 kN Year of manufacture: 2022 Weight: 151 kg Load cells: - 50 kN 2530-50kN/165541 - 5 kN 2530-5kN/166885 - 500 N 2530-500N/164475 Bluehill Universal software version 4.29.29784 provided on USB stick Software also installed on PC Last maintenance and calibration: August 2024 Next maintenance and calibration due: August 2026 3400 Series universal testing machines cover a test force range from 500 N to 300 kN. With the patented Instron Operator Protection Architecture, the 3400 Series machines are now more user-friendly, smarter, and safer than ever before. These testing systems are suitable for tension, compression, bend, peel, puncture, friction, shear, and many other types of tests and can be equipped with a wide variety of grips and fixtures from our comprehensive range of accessories. Total height: 1604 mm Maximum vertical test space (daylight opening, from base to underside of crosshead): 1198 mm Test types: Tensile, compression, and cyclic operation with zero crossing Primary control mode: Displacement control Maximum capacity – kN (lbf): 50 (11,240) Maximum speed – mm/min (in/min): 508 (20) Minimum speed – mm/min (in/min): 0.05 (0.002) Maximum force at maximum speed – kN (lbf): 25 (5,620) Maximum speed at maximum force – mm/min (in/min): 254 (10) Return speed – mm/min (in/min): 508 (20) Fsdpfxowz Ikte Aa Hegk Crosshead speed accuracy: ±0.2% of set speed at constant rate and no load Crosshead position indication accuracy: In unloaded state ±0.02 mm (0.0008 in) or ±0.10% of indicated value, whichever is greater Crosshead position reproducibility – mm (in): ±0.015 (0.0006) Load measurement accuracy: ±0.5% of reading down to 1/200 of load cell capacity Strain measurement accuracy: ±0.5% of indicated value up to 2% of full scale, with extensometer ASTM E83 class B or ISO 9513 class 0.5 We are happy to assist with financing or leasing of the offered equipment on request!

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2005, obratovalne ure: 30.408 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 50 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.250 mm, širina bale: 1.100 mm, višina bale: 720 mm, teža bale: 550 kg, skupna masa: 16.000 kg, kapaciteta rezervoarja za olje: 600 l, leto zadnje generalne obnove: 2024, Technical Specifications of the Baler: Manufacturer: Presona AB Model: LP 50 EH1 Year of manufacture: 2005 Operating hours: 30,408 hours (as of April) Number of bales produced: 198,059 (as of April) Main press force: 50 t Specific press force: 63 N/cm² Theoretical throughput: 530 m³/hour Throughput under working conditions: 260 m³/hour Feed hopper dimensions: 1,250 x 1,100 mm Press chamber volume: 2.2 m³ Bale dimensions: 1,100 x 720 mm, length variable Drive power: 22 kW Tying: 5-fold vertical, fully automatic Throughput rates at bulk density of: 30 kg/m³: 6 to 7 t/hour Fgjdpfxeu Thhro Aa Hsk 50 kg/m³: 7 to 9 t/hour 100 kg/m³: 11 to 14 t/hour Bale density (paper/newspaper): 400 to 550 kg/m³ Hydraulic oil tank capacity: 600 L PLC control: Telemecanique TSX Micro Control panel: Schneider Magelis Effective transport dimensions (excluding baler): 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight (baler): approx. 16 t Condition of the baler: The machine has been partially overhauled in our workshop and general maintenance work has been carried out. After completion of the overhaul, the baler was tested during operation and is available for sale at short notice. The following overhaul work was performed: General: - Machine cleaned, derusted, primed, and partially repainted - Wire entry marks in the press channel guideways welded and smoothed Hydraulic unit: - Hydraulic oil tank drained, tank cleaned, new oil filled - Oil filter and air filter replaced - Leaking oil sight glass on hydraulic oil tank replaced - All hydraulic hoses replaced Electrics: - Menu language set to English in the program - Two key switches on the control panel replaced - Control cabinet replaced - Signal lamp on the control cabinet replaced - Limit switch for the flap replaced - Electrics of the wirbulator renewed, connected, and tested Press ram: - All four guide rollers of the press ram removed and replaced - Main hydraulic cylinder dismantled, disassembled, and partially overhauled; cylinder barrel honed, complete seal set replaced, leak test carried out - All plastic wear pads on the press ram replaced Pre-press flap: - Both bearings on pre-press shaft replaced - Both hydraulic cylinders dismantled, disassembled, and partially overhauled; both cylinder barrels honed, complete seal sets replaced, leak test carried out - Scraper flap on pre-press replaced Tying unit: - Two complete needles with wire guide rollers replaced - Needles adjusted and set - All wire guide rollers in the needle heads replaced - Twister fingers replaced - Two twister shafts replaced - All 8 wear plates on the twist mechanism under the twister fingers replaced Scope of delivery: Only the baler is being sold. Documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. Inspection by appointment. We assume no liability for the technical details or possible errors.

Stanje: delavnici obnovljeno (rabljeno), Stock no. 2553 1 used, partially overhauled and function-tested extruder, consisting of: Material hopper Single-screw extruder BATTENFELD type UNI-EX 1-75-25 B Screw diameter: 75 mm – 25 L/D, barrel air-cooled Screw speed up to 130 rpm Drive 120 kW – DC (overhauled), drive via belt pulley Heating zone control sections for downstream equipment Control cabinet, melt pressure sensor Inspection / test run possible at short notice by arrangement at our Wuppertal facility. Matching accessories available: > Screen changer > Pelletizing (strand, hot face cut, or water ring) > Miscellaneous Fjdpfxeiyyndj Aa Hegk Further extruders and complete lines are available for demonstration ex works Wuppertal. We look forward to your enquiry or your visit.

Stanje: novo, Leto izdelave: 2024, pritisk: 8 letvica, Horizontal mitre adjustment 15°–90°15°, stepless Saw motor 5.50 kW (400 Volt) Saw blade Ø 600 mm Travel range rear stop 180 mm Working height 940–1000 mm, adjustable via feet 2 x extraction ports (top of hood and bottom) Net weight 600 kg WxDxH 135x140x150 cm RAL 9007 Grey Aluminium Rotary table made from ground nickel steel Saw head with recirculating ball guides, designed for high accuracy, long service life, and high rigidity. Material can be pre-clamped with low pressure when the hood is open. Hydropneumatic blade feed Chip flow directed toward extraction hood. Fgsdpjgwt S Tjfx Aa Hek Equipment • Precision underfloor circular saw • Mitre adjustment 0º/45º/90º/-45º/-60º, stepless • Incl. 2 pneumatic vertical clamps • Infinitely variable saw blade feed rate • Two-hand safety control • Adjustable rear material stop • Chip extraction device – chip extraction system • Mist spray unit for air-oil cooling • Air pistol with spiral hose • Incl. maintenance unit with pressure reducer • Ergonomically arranged control panel • Max. cutting height 230 mm • Saw blade Ø 600 mm • Saw blade not included in delivery! Our NC pusher system ensures your workpieces are positioned at the desired working position on our UK 600 HA 90°. A gripper clamp secures the material, and the NC control automatically positions it. Afterwards, the clamping and sawing process is activated. Positions are pre-programmed in the control system. Once the machining operation is completed by the machine, it automatically moves to the next sawing position. Depending on the workpiece, multiple parts can also be clamped and positioned simultaneously, stacked or side by side. You are welcome to inspect the desired machine at any time in our manufacturing/demo hall. Please feel free to contact us regarding this. Plantec Maschinen GmbH

Leto izdelave: 2006, obratovalne ure: 15.000 h, Stanje: dober (rabljeno), For sale is an Erema 1007T Year of manufacture: 2006 Operating hours: 15,420 Throughput: 250–350 kg/h The plant is currently processing HDPE, but it is also suitable for other plastics such as LDPE... The machine can be inspected during operation. A new extruder screw was installed in February. Fgsdpfxoumubyo Aa Hok

Leto izdelave: 2024, obratovalne ure: 10 h, Stanje: skoraj kot novo (rabljeno), Extrusion line with stuffing unit – ideal for recycling applications This robust and versatile extrusion line is optimally suited for recycling polyolefins such as LDPE, HDPE, and PP. Thanks to the integrated stuffing unit, materials with low bulk density – such as regrind, EPS, film scraps, or other lightweight plastic waste – can be processed without any issues. Fgsdpfxstziudj Aa Hjk The stuffing unit reliably compacts the loose material and feeds it directly to the extruder. This ensures consistent material intake and stable extrusion, even with challenging input materials. Advantages: • Effortlessly processes all types of polyolefins • Ideal for light and voluminous materials such as EPS or film regrind • Efficient material feed thanks to integrated stuffing unit • Compact design, easy to maintain - Feeding extruder / melt extruder - Screw diameter: 145 mm - Drive: 45 kW - Induction heating - Stuffing unit - Hopper for material feed (Suitable for low bulk density material) - Large filter / screen changer - Strand die adapted