Stroj za brizganje

KraussMaffei KM 800 - 8100 MX

Stanje: dober (rabljeno), Leto izdelave: 2011, Krauss Maffei Injection Moulding Machine KM 850-12000 MX With Krauss Maffei robot Year of manufacture: 2011 Hydraulic-mechanical two-platen clamping system with 4 pressure pads and 4 locking units on the moving platen. PV - injection unit stroke control. MC 5 control system with colour monitor, integrated control panel, and USB data carrier. Plasticizing unit Complete plasticizing unit for thermoplastics with screw diameter 135 mm, with non-return valve and open nozzle. Nozzle radius 25 mm, nozzle orifice 9 mm Cedpfx Aetrya Rsgtsha TECHNICAL DATA Clamping unit - Clamping force: 8500 kN - Opening force: 560 kN - Mounting platen dimensions (h x v): 1600 x 1600 mm - Tie bar clearance (h x v): 1140 x 1140 mm - Opening stroke: 1600 mm - Mould height (min-max): 500 - 1100 mm - Daylight: 2100 mm - Ejector stroke: 300 mm - Ejector force: 200 / 100 kN Injection unit - Screw diameter: 135 mm - Injection pressure: 1389 bar - Shot volume: 8588 cm³ - Shot weight for PS: 6098 g - Injection rate: 1414 cm³/s Electro-hydraulic equipment - Rated motor power (pump): 132 kW - Dry cycle time according to Euromap 6: 965 1/h - Oil tank capacity: 2440 l Weight and dimensions - Net weight with control cabinet: 49 t - Installation space (L x W x H): 11.72 x 2.92 x 2.71 m

Stanje: novo, *Technical Standard Specification: Heater output: 9 kW Cooling capacity: 50 kW Medium: water up to 160°C Maximum external volume: 16 liters at 160°C Max. flow rate: 57 l/min Max. delivery pressure: 6.0 bar Dimensions (L x W x H): 780 x 305 x 705 mm Weight: approx. 80 kg HIGHLIGHTS / FEATURES: • Smart Controller Plus 7" touch screen / Industry 4.0 compatible • Flow measurement, configurable flow alarms • Return temperature display • Frequency inverter for pump speed control with automatic mode for energy-optimized operation, or adjustable flow rate (within the operating range of the temperature control system) • Electronic pressure sensor in the supply line • Interface via 9-pin D-Sub connector 20mA/TTY • Connection for external PT100 temperature sensor for measuring and displaying tool temperature • Continuous bypass of heat exchanger via 3-way valve to reduce deposits in heat exchangers • High-performance pump, hydraulic components in stainless steel (VA), magnetically coupled • Tool draining via suction • Booster pump for unit filling at high temperatures • Filling via cooling water, switchable to separate filling • SSR for heating control • IP54 splash protection Visit our website for more details or for other performance classes. Cedpfx Agjftm Hretoha *This unit complies with European directives. Other directives and standards are only fulfilled if listed in the order confirmation. This technical specification reflects the standard equipment; customer requirements deviating from standard will be stated in the quotation or order confirmation.

Stanje: dober (rabljeno), Leto izdelave: 2007, Znamka: Mori Seiki Tip: NT3200 Letnik izdelave: 2007 Serijska številka: NT320GA0030 Dodatne informacije: Delovni čas: 7976 ur Največji premer obdelovanca (glava za rezanje): 600 mm Največji premer obdelovanca (revolverska glava): 210 mm Chjdpoxn Ddtefx Agtsa Največja dolžina obdelovanca: 500 mm Premer vretena: 67 mm Število mest za orodje: 40 Vreteno: Kitagawa SS1666 Hitrost vretena: 5000 vrt/min Krmilni sistem: Fanuc Series 31i Oprema: nastavitev orodja, filter za oljno meglico Absolent AB, transporter za струžine Enomoto, filter za hladilno tekočino Ercoatius, dokumentacija Glava za rezanje Največja hitrost: 12000 vrt/min Velikost gredi za orodje: C5 Gib osi X: 685 mm Gib osi Y: ±125 mm Gib osi Z: 1075 mm Gib osi B: ±120° Hitrost gibanja osi X/Z: 50 m/min Hitrost gibanja osi Y: 30 m/min Revolverska glava Število mest za orodje: 12 Hitrost orodja: 6000 vrt/min Gib osi X: 130 mm Gib osi Z: 970 mm Hitrost gibanja osi X/Z: 30 m/min Dimenzije stroja (D x Š x V): 5200 x 3100 x 3000 mm Lastna teža: 14400 kg Vključno z nosilcem palic Znamka: Iemca Tip: VIP 80E II Letnik: 2007 Serijska številka: 020710QA07 Lastna teža: 605 kg Kapaciteta palic: 6-80 mm

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2008, obratovalne ure: 6.200 h, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 4.200 kN, premer vijaka: 75 mm, Krauss-Maffei KM 420-2000 CX Injection moulding machine from Krauss-Maffei with a 420-tonne clamping force. Only 6,000 operating hours in automatic mode. Year of manufacture: 2008. MC5 control system. Screw diameter: 75 mm. Extras include: 8 hot runner zones, 2 core pulls on the fixed platen, 2 core pulls on the moving platen, 1 pneumatic valve on the moving platen. The injection moulding machine is delivered REFURBISHED by the UK Transitus technical expert team. Commissioning at customer facilities can be offered, ensuring machine functionality upon installation completion. Technical Details SCREW DIAMETER: 75 mm INJECTION PRESSURE: 1635 BAR INJECTION VOLUME: 1237 cm³ INJECTION WEIGHT: 1126 g MAXIMUM DISTANCE BETWEEN PLATENS: 1400 mm MINIMUM MOULD THICKNESS: 380 mm OPENING STROKE: 1020 mm TIE BAR DISTANCE: 900 x 800 mm PLATEN DIMENSIONS: 1270 x 1230 mm Cjdpfxewq D Efo Agtjha SCREW DIAMETER: 75 mm CLAMPING FORCE: 4200 kN YEAR OF MANUFACTURE: 2008 OPERATING HOURS: 6282

Stanje: novo, *TECHNICAL SPECIFICATION: Heating capacity, hot circuit: 48 kW Heating capacity, cold circuit: 12 kW Cooling capacity, hot circuit: 42 kW Cooling capacity, cold circuit: 270 kW Medium: Water up to 200°C Maximum external volume: 10 liters at 200°C Max. flow rate: up to 200 l/min Max. delivery pressure: up to 6.5 bar Motor power: 5.5 kW Dimensions (LxWxH): 1,395 x 753 x 1,180 mm Weight: approx. 580 kg *EQUIPMENT HIGHLIGHTS: - Control and operation via PLC with touch screen - Heating with stainless steel tubular heaters made of Incolloy - Heater control via solid-state relays - Control cabinet IP54, externally ventilated - Electrical wiring on terminal blocks - Volt-free input for signal to switch between heating/cooling (front door) - Volt-free contact for collective alarm via 3-pin connector (front door) - Temperature control unit with heating and cooling circuits, for connection to a valve station for rapid switching between hot and cold circuits Cjdpfx Agsg Ey Ufetoha - Temperature-controlled feed of return water - Level monitoring with automatic level compensation - Dirt filters in cooling water inlet and in return line of the circulation system - Separate automatic filling with strainer - Flow measurement using differential pressure principle in both circuits - Monitoring of heating element surface by temperature sensor - System pressure regulation, required compressed air connection: 6 to 8 bar - Pressure boosting pump type DS 360 for make-up water - Corrosion-resistant components (stainless steel, brass) - Unit mounted on castors and ready for connection *OPTIONS: - EcoTemp system for intermittent operation - Connection for external temperature sensor PT100 or type J/K - Remote touch screen with 15 m cable Visit our website for more details or for alternative performance classes. *This unit is compliant with European directives. Other directives and standards are only fulfilled if specified in the order confirmation. This technical specification reflects the standard configuration; customer-specific deviations from the standard are listed in quotations or order confirmations.

Stanje: pripravljen za uporabo (rabljen), Vertikalni obdelovalni center Mori Seiki MV-Junior... Orodni magazin za 30 enot, pomik X: 560 mm; Y: 410 mm; Z: 460 mm, dimenzija mize: 900x450 mm, maksimalna nosilnost mize: 300 kg, maksimalna hitrost vretena: 8.000 vrt/min, skupna teža: 3.900 kg Chedex I D Syepfx Agtsa

Stanje: kot nova (razstavni stroj), Leto izdelave: 2024, obratovalne ure: 800 h, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 1.250 kN, izmetalna sila: 25.000 N, CNC All FANUC Roboshot are FULL ELECTRIC -warranty -only 62 hour FANUC Roboshot S100iB 2024 (only 800 hours) The machine was used at trade fairs as a demo unit and is practically new. Clamping force: 125 tons Cjdpfeya D I Dox Agtsha Screw diameter: according to customer requirements All additional equipment is configurable according to customer needs and can be upgraded to meet specific application requirements. Additional optional equipment: -FIBER sorting flap (for separation of good and defective parts) -Hot runner controller (integrated and connected to the machine) -V-gate -Additional electrical sockets -Electrical quick coupling for fast mould change -Water piping system -Mouldflo system for digital monitoring of water flow, temperature, and pressure -Machine elevation by 100 mm -Hydraulic power unit for side cores (2CH / 4CH) -Robot (cartezian STAR robot) -Robot ( 6axis FANUC Robot) -and so on This machine is available for Slovenia, Croatia, Bosnia and Herzegovina, and Serbia.

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2013, potovalna razdalja osi X: 1.067 mm, pomik osi Y: 610 mm, pomik po osi Z: 610 mm, skupna masa: 6.850 kg, število mest v zalogovniku orodij: 24, število osi: 3, Ta 3-osni stroj Hurco VMX 42i je bil izdelan leta 2013 in ima pomik po osi X 1067 mm, po osi Y 610 mm in po osi Z 610 mm, z orodnim držalom SK40. Če iščete kakovostni rezkalni stroj, razmislite o Hurco VMX 42i, ki ga imamo v prodaji. Za več informacij nas kontaktirajte. • Ure vretena: pribl. 12.603 h • Skupna potrebna moč: pribl. 28 kVA Dodatna oprema Chsdpfsy Tw Ryex Agtsa • Transporter ostružkov • Notranji hladilni sistem Tehnična specifikacija Velikost stožca SK 40

Stanje: dober (rabljeno), Leto izdelave: 2016, Kontaktirajte za več informacij Chodpfx Agjy Enr Sjtoa

Stanje: novo, *TECHNICAL SPECIFICATIONS: Heating capacity: up to 54 kW Cooling capacity: up to 300 kW Medium: Water up to 200°C Maximum external volume: 43 l at 200°C Max. flow rate: up to 230 l/min Max. delivery pressure: up to 8.3 bar Chjdpfxsg Ey T Ee Agtoa Motor power: up to 3 kW Dimensions (LxWxH): 1,460 x 525 x 1,200 mm Weight: approx. 330 kg Heat transfer medium connection: Flange DN40 (DIN EN 1092-1), Form B1 *FEATURE HIGHLIGHTS: - Smart controller (7" touch display) for regulation and control - Heating control via solid-state relays - Control cabinet IP54, externally ventilated - Expansion vessel, heater, and piping made of stainless steel - Heating via stainless steel tubular heater made of Incolloy - Dirt trap (circulation) - Unit ready for connection and mounted on castors, 2 of which are steerable and equipped with brakes - Cooling and filling controlled via solenoid valve - Configurable automatic filling via potable water supply or separate connection (factory setting: via cooling water supply) - Flow measurement by differential pressure principle - Level monitoring via magnetic float switch - Automatic temperature-dependent system shut-off (except for WP7-90) - Flow monitoring by flow detection - Bypass between flow and return with reduced cross-section - Dirt filters in cooling water supply, filling, and return line of the circulation system - Continuous bypass of heat exchanger via 3-way motorized control valve (WP7-180/200) - System pressure monitoring using pressure transmitter in the expansion vessel (WP7-150/180/200) - Booster pump for system filling (WP7-180/200, optional for others) - Safety temperature limiter (STL) in heater and supply line (WP7-200) - Manometer in supply line at rear side of the unit - Circulation circuit thermally insulated (WP7-150/180/200) Visit our website for more details or for other performance classes. *This device is compliant with European Directives. Other directives and standards are only fulfilled if stated in the order confirmation. This technical specification reflects the standard configuration; customer requirements deviating from the standard are specified in quotations or order confirmations.