CNC univerzalna rezkalna naprava

KLOPP FWS15

Stanje: dober (rabljeno), Leto izdelave: 2007, potovalna razdalja osi X: 750 mm, pomik osi Y: 750 mm, pomik po osi Z: 725 mm, CNC control Sinumerik 840D NC rotary table B-axis Magazine for 320 tools Pallet changer device, 2 pallets 500mm x 500mm Internal coolant supply ICS (80 bar) Chip conveyor Coolant system Technical data: X-travel longitudinal: 750 mm Y-travel vertical: 750 mm Z-travel cross: 725 mm B-axis: 360° Spindle taper: HSK 63A Spindle speed range: 50–10,000 rpm Tool positions in changer: 320 Feed rate: 60,000 mm/min Rapid traverse: 60 m/min Spindle drive capacity 40/100% duty cycle: 37/24 kW Machine weight approx.: 15,000 kg Technical data, accessories and machine description are not binding. Hjdpfxeq Ui Hqj Altsr

Stanje: skoraj kot novo (rabljeno), Funkcionalnost: popolnoma funkcionalen, Weiler Commodor Lead and Feed Screw Lathe with 3-axis K&C Digital Readout, newly overhauled, including acceptance protocol for new machine tolerances Technical Data: Hodpfx Alsymznhetsr >> Machine No.: 2268-87 >> Centre height: 180 mm >> Distance between centres: 1000 mm >> Spindle speeds: from 13 to 2000 rpm >> Spindle bore: 56 mm >> Short taper spindle nose DIN 55029 Camlock >> Tailstock: MT 4 >> Feeds from 0.026 to 0.888 mm/rev >> Possible threads: Metric, Inch, Module, and Diametral Pitch >> Metric thread pitches from 0.35 to 12 mm >> Weight approx. 1500 kg >> Switchable spindle brake >> Drive power: 2.0/4.0 kW >> Dimensions: length 2.2 m, height 1.5 m, depth 1 m Accessories and Equipment: >> New K&C 3-axis digital readout, 12 months manufacturer’s warranty, with operating manual >> New 200 mm 3-jaw chuck, 2 sets of jaws >> Multifix size B with 3 new tool holders >> Bed stop >> Machine mounts >> Coolant system >> LED machine lamp For safety, the machine is equipped with: >> Electronic spindle guard >> Spindle brake >> 2 emergency stop buttons On request: Covers for lead and feed screws About the machine: Offered here is a Weiler Commodor lead and feed screw lathe, geometrically overhauled. The guides have been reground or newly scraped. Acceptance according to inspection protocol. Painted in 2K glossy white. Accessories such as Multifix and chuck are new. For safety: The machine features a brake motor, electronic spindle guard, and two emergency stops. This is an as-new condition lathe. Even at high spindle speeds, the Weiler runs very smoothly. This newer generation of Weiler lathes is extremely operator-friendly and allows for ground-like surface finishes. Take the opportunity to view and test this machine on site under power and see the condition for yourself.

Stanje: dober (rabljeno), Leto izdelave: 2009, Stroj bo prispel z robotom. 42.000 vrt/min Hodpfx Aexfu S Nolter

Stanje: rabljeno, Leto izdelave: 2000, Grinding diameter: 360 mm Grinding length: 1600 mm Centre height: 180 mm Internal diameter: 0 mm Grinding depth: 0 mm Swing diameter: 0 mm Total power requirement: 40 kW Machine weight approx.: 10,000 kg Hedpfx Alst Hw Rdstsr Space requirement approx.: m KARSTENS Universal "CNC" External, Internal and Face Grinding Machine with capabilities for multi-sided, non-circular, polygon, and thread grinding BWO CNC control Type 900 C, Type K 51-1500 Year of manufacture: 2000 Serial no. 99 033 _____ Centre height: 180 mm Centre distance / Grinding length: 1,700/1,600 mm Max. workpiece weight between centres: 250 kg External grinding: Grinding diameter approx.: 5 - 360 mm Grinding wheel size (diameter x width x bore): 500 x 100 x 127 mm Grinding spindle speeds (35 m/s / 50 m/s): 1,900 / 2,200 rpm Drive power external/face/internal: 7.5 / 7.5 / 4.0 kW Grinding spindle head: 3 positions B-axis swivel range: 240 / 17.5 ° X-axis / Cross slide stroke: 360 mm Grinding slide feed rate: 0.001 – 125 mm/min Workpiece spindle speeds, steplessly adjustable: 1 – 1,000 rpm C-axis spindle mount / Bore, 24 mm MK 4 Table feed (Z-axis): 0.01 – 10 m/min Total drive power: 40 kW - 400 V - 50 Hz Weight approx.: 10,000 kg Accessories / Special features: Universal CNC cylindrical grinding machine for almost all grinding tasks, suitable particularly for non-circular grinding / eccentric & cam profile grinding, polygonal grinding, as well as face grinding of multi-sided workpieces and even thread grinding with corresponding grinding wheel profiles. Freely programmable BWO CNC controller with numerous subprograms and easy parameter input. Grinding of multiple diameters in a single clamping possible. - B-axis with three grinding spindles, one with MOVOMATIC touch probe - MOVOMATIC pneumatic diameter gauge CR 60 for mounting on the grinding table, control unit type ES 400 - MPM grinding wheel balancing unit, straight dresser with diamond fleece mounted on table, powered diamond wheel dressing device - Workpiece spindle head pneumatically movable, hydraulic tailstock with adjustable quill - Various further accessories, but without coolant equipment Condition: good to very good – demonstration possible under power Ideal machine for spindle manufacturing, etc. Delivery: ex-stock – as inspected Payment: strictly net – upon receipt of invoice

Stanje: rabljeno, Leto izdelave: 1957, Premer struženja nad posteljo: 800 mm Premer struženja nad suportom: 540 mm Dolžina struženja: 4000 mm Višina konic: 400 mm Razdalja med konicama: 4000 mm Vrtljaji vretena: 9 - 1140 o/min Premer vretena: 96 mm Hedpfx Alexwp Ehetor Teža stroja pribl.: 8,5 t Dimenzije stroja (D x Š x V): 7,0 x 1,70 x 1,70 m - z mostom - Oprema: Trivrata vpenjalna glava FORKARDT 400 mm, štirivrata vpenjalna glava 500 mm, čelna plošča 800 mm, digitalni prikaz na oseh X in Z ACU-RITE, Glava MULTIFIX z več vložki, 2 fiksna luneta, 1 gibljiva luneta, sredinski konic, naprava za hlajenje

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2026, premer spodnjega valja: 310 mm, premer zgornjega valja: 320 mm, premer valja: 310 mm, dolžina valja: 1.550 mm, delovna širina: 1.500 mm, najv. debelina jeklene pločevine: 38 mm, skupna masa: 12.500 kg, skupna dolžina: 4.500 mm, skupna širina: 2.300 mm, skupna višina: 1.740 mm, moč: 18,39 kW (25,00 KM), delovna dolžina: 1.500 mm, Oprema: dokumentacija / priročnik, nujno zaustavitev, FACCIN HAV 15342 Variable 3-Roller Plate Bending Machine Electronically controlled, hydraulic 3-roller plate bending machine Technical Data: Number of rollers: three Hjdjt Akt Rspfx Altjr Side roller geometry: variable Working width: 1,550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressing force against top roller: 160 tons Working pressure at rated capacity: 250 bar Guaranteed installed power: 18 kW (25 HP) Guaranteed max. rotation speed: 3.5–7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed Performance: for material with yield strength 260 N/mm² Rolling capacity (full working width): 38 mm Pre-bending capacity (full working width): 20 mm from pipe diameter: 1,600 mm Rolling capacity (full working width): 30 mm Pre-bending capacity (full working width): 17 mm from pipe diameter: 415 mm Standard Equipment: Variable geometry with linear guides for roller movement Extra-long swing arm bearing for increased frame stability Electronic Parallelism System EPS Hardened rollers for high wear resistance All rollers ground after heat treatment Siemens S7-HMI PLC control PGS-CLASSIC control with Siemens touch panel High-tech hydraulics and electrics package Simultaneous rotation and roller movement Safety emergency cable with emergency stop and CE certification Centralized lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting supports and roller conveyors FACCIN Advantage Package AP

Stanje: dober (rabljeno), Leto izdelave: 1980, številka stroja/vozila: 27-3, Offer 23317 Technical Data: - Max. working width: 2040 mm - Max. material thickness at 40 kp / mm² strength: 3.5 mm Hsdpferklfrox Altjr - Bending angle adjustment, electronically pre-selectable: 0 to 135° - Smallest bending radius: 1.25 x sheet thickness - Minimum internal flange height: 6 x sheet thickness - Automatic sequence control for a complete work cycle - Operation via hand or foot switch - Maximum opening width / stroke of upper beam: 200 mm - Height adjustment: - of the bending beam: 80 mm - of the lower beam: 80 mm - Upper beam drive: 400 V / 1.1 kW - Bending beam drive: 400 V / 1.5 kW - Manual backgauge, accessible from the front - Required space (approx.): W 3300 x H 1350 x D 1500 mm - Weight (approx.): 2600 kg

Stanje: zelo dobro (rabljeno), 3-phase direct current spot welding machine DALEX Type PMS 11-4 G 3 Rated power at 50% duty cycle: 96 kVA Secondary short-circuit current: 44.5 kA Hjdohmvawspfx Altsr Secondary open-circuit voltage: 4.72 V Electrode force: 100–600 daN Arm reach: 550 mm with mounted control cabinet according to VDE 0100 Main switch Synchronous welding controller 8033 Weight: 740 kg

Stanje: zelo dobro (rabljeno), Leto izdelave: 1998, Funkcionalnost: popolnoma funkcionalen, premer struženja nad prečnim suportom: 570 mm, izvrtina vretena: 62 mm, stružna dolžina: 1.250 mm, premer struženja nad ležiščem sani: 365 mm, višina središča: 280 mm, skupna masa: 4.000 kg, O F F E R We can offer you, subject to prior sale and errors excepted, ex stock without obligation: V D F - BOEHRINGER Cycle-Controlled Universal Lathe Model DUS 560 Year of manufacture 1998 / completely overhauled in 2008 --- Centre height 280 mm Max. swing diameter over bed 570 mm Max. swing diameter over cross slide 365 mm Cross slide/traverse travel 345/125 mm Distance between centres / max. turning length 1,250 mm Spindle bore 62 mm Infinitely variable spindle speeds, 2 ranges 3-500 / 15-2,500 rpm Infinitely variable longitudinal and cross feeds 0.01-50 mm/rev Rapid traverse longitudinal/cross 5 / 10 m/min Max. feed force cross/longitudinal 6.5 / 12.5 kN Max. workpiece weight between centers/with tailstock 400 / 1,000 kg Thread pitches 0.1 – 400 mm/pitch Spindle drive 15/21 kW Total drive 25 kW – 400 V – 50 Hz Weight approx. 4,000 kg Accessories / Special Equipment: Hjdpsyqw Eqsfx Altsr • SIEMENS 2-axis cycle control Type 805 with direct input of all turning parameters via interactive interfaces and corresponding software; control and monitor integrated in the sliding door; with memory expansion and software for free contour programming, graphics, etc. • 2 electronic handwheels for fine adjustment of carriage travel in Z and X axes, and new joystick for rapid traverse +Z/-Z and +X/-X; Joystick for the main spindle with infinitely variable speeds – forward and reverse • Mounted 3-jaw chuck Model SCA Ø 300 mm, faceplate approx. Ø 500 mm, 4-jaw chuck Ø 315 mm, driving plate approx. 250 mm, single faceplate 500 mm, various jaws. • Mounted MULTIFIX toolpost Type CD with 5 different Multifix holders • Separate tool block for CAPTO tool holders with internal coolant supply, various holders partly with collet chucks • Tailstock with air bearing for easy movement, work lamp • Movable chip trolley with coolant pump and oil skimmer, 2 rear sliding doors • Separate control cabinet, adjustable spindle end stop, work lamp, etc. Condition: very good – guides in very good condition, available for demonstration under power Please click here for a video of the machine: Delivery: ex stock – as inspected Payment: strictly net before delivery We look forward to your order. More lathes of all sizes available in stock – please inquire.

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2023, Mandrel Bending Machine S4501 ----- For the production of tube geometries with bending radii from 1.5xD → Maximum bending capacity, tube 42.4 x 3.25 mm (steel max. Re 240 N/mm²) → Maximum bending capacity, tube 30 x 30 x 3 mm → Maximum bending capacity, tube 42.4 x 2 mm (stainless steel VA 0.2 260 N/mm²) → Total connected load 3 kW → Tube feed-in length approx. 1.5 m Robust and durable steel construction. Maintenance-free servo drive for the bending, feed, and rotation axes. The control system's touch display allows for easy and intuitive programming and operation of the machine. After the tube is inserted, it is fixed in place by the chuck in the carriage, ensuring precise positioning and permitting the production of dimensionally accurate geometries. Standard features also include a tube geometry check before the bending process: if the bending process is started at the wrong position, the machine will not release the bending operation—misoperation is prevented. Optional additional features increase comfort, boost output, and thus enhance the system’s efficiency. Data exchange with the optional TBS-3D pipe calculation software (PC version) is done via USB stick or network. Existing tube geometries can be imported using the software. Standard features: → Servo drive on bending axis, 1.5 kW → Adjustable rotation speed → Left-hand bending direction → Bending angle resolution 0.1° → Max. bending radius 120 mm → Bending shaft diameter 50 mm → Servo-driven feed → Servo-driven rotation Hodpfx Aljtr U Hljtsr → Three-jaw chuck for clamping the tube in the carriage → Pneumatic tool retraction Hydraulics: → Hydraulic tube clamping with adjustable clamping force → Programmable early mandrel retraction PLC control: → 10" colour touchscreen → ETH 10/100, X2X Link, 2x USB → Foot switch operation → Data transfer via LAN or USB → Material database Unique graphical programming: Simple geometries can be calculated directly at the machine. After entering length and angle, the controller automatically calculates the feed values and bending angles. Power supply: 400V 16A Dimensions: L: 2.3 m x W: 1 m x H: 1.4 m Weight: approx. 1200 kg