Odprta polprikolica s ponjavo

KÖGEL 3-Achs-Cargo-Coil-Pritschensattelanhänger

Our complete stock of vehicles, including those available immediately or at short notice, can be found on our website.

Itodpevl N N Tjfx Ah Dsn
Excerpt from the specification. Full specification available on request.

Chassis
* Regular ladder frame in lightweight steel construction with inserted cross members
* Distributed load max. 30 t evenly spread over approximately 1.5 m around the payload center
* Coupling plate approx. 8 mm thick, with a 2" fifth wheel kingpin according to DIN 74080 / ISO 337
* Coil well, internal length approx. 9,000 mm (shape according to VDI guideline 2700) for accommodating coils with a diameter of min. 900 mm up to max. 2,100 mm

Running gear
* Axle lift mechanism on axle 1
* Fully automatic axle lift control, load-dependent

Starting aid
* Activation by braking three times, 30% overload up to a speed of 25 km/h
* Operation on the chassis via switch
* Additionally possible from the driver’s cab (switch in cab required – PIN 12)

Three-axle SAF INTRADISC module
* With disc brakes, diameter approx. 430 mm, ET 120
* Air suspension with approx. 180 mm travel

Vehicle tyres
* 6 x 385/65 R 22.5, 160J
* 6 steel rims 22.5 x 11.75, offset approx. 120 mm (ET 120)

Chassis attachments
* Mechanical landing legs with compensating foot, 24 t lifting capacity, one-sided operation on the right in the direction of travel
* Spray suppression system in accordance with Regulation (EU) No. 109/2011 for three-axle module with 385/65 R22.5 tyres, consisting of 1 pair of quarter-circle mudguards ahead of the axles, 1 pair of straight mudguards with spray flaps between 1st and 2nd axle, and 1 pair of quarter-circle mudguards with spray flaps behind the axles
* Side underrun protection to ECE-R73
* Holders for 8 square plug-in posts, internal dimensions approx. 340 x 220 x 2,150 mm, installed behind the axle group
* 2 waterproof plastic toolboxes, internal dimensions approx. 545 x 400 x 400 mm. Mounted at the rear, 1 left and 1 right

Brake / air suspension system
* EBS system 2S/2M with stability program (includes ABS/ALB function)
* Air suspension system including 1 lift/lower valve, mounted on the left in the direction of travel, behind the axle group
* Driving position adjusts automatically

Floor
* Mounted version on both sides
* Steel pallet stop rails with VarioFix hole pattern (bolted) on the left and right in the direction of travel, for internal width approx. 2,468 mm (internal loading height below outer rail is reduced by approx. 20 mm)
* Laminated plywood floor, approx. 30 mm thick, with cut-out in the area of the coil well
* Coil well side walls lined with plywood panels, approx. 18 mm thick
* All-round jointed coil well cover made entirely of wood, with floor panels approx. 27 mm thick
* Stake pockets for square plug-in posts, approx. 80 x 80 mm, arrangement according to drawing A2, 2 pairs on the longitudinal beam in 1st and 2nd position, 8 pairs in the outer frame
* 8 pairs of stake pockets in the coil well for square plug-in posts approx. 80 x 80 mm, arrangement: 1st pair at the front of the well, 2nd–7th pairs as per standard drawing, 8th pair at the end of the well

Superstructure
* Quick-release device at front for side curtain, with tension rods and deflection lever
* Quick-release device at rear for side curtain, with tension rods and ratchet
* Complies with body strength according to EN 12642 XL (VDI 2700), tested for a payload of approx. 27,000 kg

Rear wall
* Double-wing rear portal door made of aluminium, approx. 2,630 mm internal

Oglas je bil preveden samodejno, zaradi česar je morda prišlo do napak pri prevodu.