Stiskalnica za furnir

Joos HP 120

Stanje: rabljeno, Leto izdelave: 2024, Version: Joos A.B.S. safety system for protecting the heating plates in case of incorrect loading or forgotten parts. The press is open on all sides, designed in a stable all-steel construction and protected against overload. The maintenance-free hydraulic system is installed in the oil tank. The continuously variable pressure adjustment is performed according to a clear pressure diagram. Once the set pressure is reached, the system automatically shuts off. Constant pressure is maintained throughout the entire pressing cycle. The rack-and-pinion guide ensures stable, parallel travel of the press. The machine is optimally suited for laminating flat surfaces with adhesives when equipped accordingly. Technical data: - Maximum pressing force: 1,200 kN - Adjustable range: 10 – 100% - Total pressing area: 3,100 x 1,350 mm - Specific pressure at full load: 3.0 daN/cm² (kg/cm²) Cgedjxplbcopfx Afnsp - 6 cylinders, 80 mm diameter, 400 mm stroke - Hydraulic operating pressure: 398 bar - Pressing space height: 400 mm - Light grey, RAL 7035 Hydraulics: The following components are installed in the press’s hydraulic system: - 1 oil-hydraulic dual-stage high-pressure pump - 1 three-phase motor, 2.2 kW - 1 automatic pressure switch - 1 changeover valve - 1 pressure diagram The hydraulic unit is located in the lower part of the press. Control: Automatic pressure regulation via electronic controller with target and actual value display. Operation is via an intuitive control panel. The control cabinet is fully integrated lengthwise in the upper section of the press. Operating voltage: 400 V, 50 Hz, 3-phase. EL-HEATING PLATE 3100 x 1350 GOLD ANODIZED: One upper and one lower electric heating plate, each 3100 x 1350 mm. Surfaces are anodized, making them extremely hard, scratch and wear resistant. Thermal high-pressure insulation between heating plate and press table. Maximum operating temperature: 120°C. One deck / 2 heating plates. TEMPERATURE CONTROL: Temperature control R 1.1: each heating plate is equipped with an electronic temperature controller and a safety temperature limiter at the edge. SWIVEL BUTTON OPERATION: Intuitive operation via a clearly arranged swivel button panel. Location: Rieth

Stanje: rabljeno, Leto izdelave: 1993, Häwa stroj za luščenje hlodovine s frezalno glavo H249 / 1000 Leto izdelave 1993 Premer hloda 0,25 m – 1,2 m Dolžina hloda 1,8 m – 7 m Frezalna glava: 30 kW Reduktor korenin: 37 kW Vsebuje: Prečni dovajalni transporter Stroj za luščenje Cgsdpfsx Rv T Isx Afnsp Transportni trakovi Odtokovni transporter

Stanje: novo, Leto izdelave: 2024, Reduce setup times by 4-5 times with pneumatic automatic tool change and a tool length sensor! Convenient operation. This CNC milling machine is suitable for cutting and engraving wood, MDF, chipboard, acrylic, plexiglass, PVC, composites, and aluminum. The Wattsan M3 1325 features an increased frame thickness, allowing it to handle heavy workpieces. It is capable of manufacturing parts for the light industry, interior and exterior decoration, souvenirs, outdoor advertising, processing of soft metals and stone, woodworking, and furniture production. For more information, you can call our managers! Features of the Wattsan M3 1325: - Working area: 1300x2500 mm - Positioning accuracy: 0.03 mm - Spindle: 7.5 kW - Machine dimensions: 1960x3350x1740 mm - Weight: 830 kg Virmer not only offers top-quality machines, but also service and delivery. Our engineers and managers are ready to answer all your questions and provide video support if needed. In addition, owners of Wattsan equipment receive lifetime online support. Virmer is based in the Netherlands and operates throughout Europe. Virmer is the official supplier of Wattsan. We supply not only laser engravers, but also metal cutters, welding machines, marking systems, and cleaning equipment. Wattsan is a Chinese manufacturer that has been producing laser equipment for nearly 15 years and is continuously developing with the help of its customers. Thanks to customer feedback, Wattsan has implemented more than 50 upgrades, making the machines more reliable, precise, and powerful, so you can take your business to the next level. YOU CAN WRITE OR CALL US! WE WILL SELECT THE RIGHT MACHINE FOR YOUR TASK If you are looking for the right laser or CNC milling machine, we are happy to assist you. Cgedpfsrywtqex Afnjp At our company, you will find a large selection of laser machines and equipment: CO2 laser machines; laser cutting machines for metal; metal laser cutters; fiber metal lasers; fiber metal laser engravers; CNC milling machines for metal; milling machines for wood; CNC milling machines; laser engraving machines; laser engravers; laser cutting machines for plywood; laser engravers; laser cutting machines for metal; CNC milling machines; laser markers; lenses; chillers; machine cooling systems; S&A chillers; IPG Laser, MAX Photonics, Raycus; compressors; rotary devices; mirrors for laser machines.

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2025, obratovalne ure: 2.000 h, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 1630, skupna masa: 7.800 kg, trajanje garancije: 6 meseci, moč: 85 kW (115,57 KM), Prodaja se kompletna proizvodna linija na osnovi briketirke Di Più BRIK MB100 (complete production line). Generalno obnovljen stroj DI PIU BRIK MB100 (tovarniško obnovljen leta 2025), pripravljen za takojšnje delovanje. Stroj je namenjen visokozmogljivemu briketiranju. Primeren je za zahtevno industrijsko uporabo. Stroj ima za seboj približno 2.000 delovnih ur. Stroj je na novo obnovljen v tovarni Di Piu, zamenjani vsi vitalni deli, vsi kabli, električna napeljava, ter potrebna električna oprema. S čimer je stroj dan v stanje novega in ima 6 mesečno tovarniško garancijo proizvajalca Di Piu. Stroj lahko proizvaja brikete z luknjo ali brez, debeline 90mm do 110mm iz mehkega in trde lesa, okrogle ali kvadratne. Ogled stroja je možen v tovarni v Italiji: Di Più Systems Srl, Via dell’Innovazione 11, 36042 Breganze (VI), Italija Mehanska briketirka Di Piu BRIK MB100 je avtomatski stroj za stiskanje lesa, žagovine in drugih odpadnih materialov v lesne brikete. Idealna vlažnost vhodnega materiala je med 8 % in 12 %, velikost delcev pa med 1 mm in 12 mm. Tehnični podatki: -Kapaciteta proizvodnje: 1.300 – 2.300 kg/h (pri gostoti žagovine 160–200 kg/m³) -Premer briketa: 90 – 110 mm -Moč glavnega motorja: 75 kW -Skupna instalirana moč: 98 kW Csdpfx Afswrp Emsnsgp -Tlak stiskanja bata: 2.000 – 2.500 kg/cm² -Vertikalni polž z reduktorjem: 5,5 kW -Oljna črpalka: 1,5 kW -Oljna črpalka za zapiranje iztiskalne glave: 1,5 kW -Dozator s polžem in nastavljivo hitrostjo: 1,5 kW -Oljni sistem za mazanje bronastih ležajev: 100 litrov -Senzor za nadzor izhoda briketov (samodejni izklop ob izpraznitvi materiala) -Zaščitne obloge gibljivih delov -Senzor tlaka olja -Krmilna omarica -Zalogovnik za vhodni material (akumulator) -Senzor nivoja za nadzor napajalnega sistema -Teža stroja: cca 7.800 kg Stroj je opremljen z vsemi pripadajočimi dodatki za popolno delovanje in integracijo v linijo za briketiranje: DODATNA OPREMA – MB100: - Dozirni silo: Izdelan iz masivne jeklene konstrukcije. Premer: 1500 mm, višina: 1000 mm. Vgrajen ima rotacijski rezalnik z reduktorjem 2,2 kW, nameščen na robustno jekleno ogrodje. Dovajanje materiala nadzira senzor nivoja. - Linija za hlajenje briketov po iztiskanju, skupne dolžine 20 metrov - Avtomatska žaga za razrez briketov - Žaga samodejno reže brikete na dolžine, ki jih predhodno nastavi operater. - Naprava za proizvodnjo briketov z luknjo - Sistem za hlajenje glave stroja z ledeno vodo - Sistem proizvaja 50 litrov/minuto ledene vode za učinkovito hlajenje glave briketirke. - Zračno hlajen hladilnik vode z hermetičnimi spiralnimi kompresorji, mikroprocesorskim krmiljenjem in velikim rezervoarjem za shranjevanje energije, v katerem je potopljen izmenjevalnik toplote voda–hladilno sredstvo. - Izmenjevalnik toplote je visokoučinkovit tipa “fin-pack”, izdelan iz bakrenih cevi in aluminijastih lamel. - Rezervoar za vodo prostornine 800 litrov - Črpalka za dovod vode (50 l/min – 20 m.c.a. – 0,55 kW) s trikrožnimi ventiloma DN25 za uravnavanje temperature hladilne vode v glavi briketirke. - Digitalni elektronski regulator temperature povezan s senzorjem NTC (merilni element d.6 × 52 mm, IP68, AISI 316). DODATNO: NOVAPAC pakirka Možnost dodatnega nakupa pakirke NOVAPAC, ki je popolnoma kompatibilna s strojem Di Più BRIK MB100 in drugimi stroji, idealna rešitev za avtomatsko pakiranje neposredno po stiskanju. Letnik: 2013 Cena za Novapac: 19.000 € Oprema vidna na zadnjih 6 slikah

Leto izdelave: 2008, stanje: zelo dobro (rabljeno), Oil burner Weishaupt WM-L10 Year of manufacture: 2008 We speak Russian! Viewing by prior telephone arrangement only! Preferred sale to dealers, tradespeople, or for export. All information provided without guarantee. Subject to errors and prior sale. The seller accepts no liability for typing errors or transmission mistakes. Csdpfx Afsi Ap Atensgp We are happy to purchase your used boiler or burner! Of course, we also handle all formalities. Loading is possible.

Leto izdelave: 2001, stanje: skoraj kot novo (rabljeno), Double-aggregate sander, two lower aggregates with 2 x 7.5 kW main motor power, feed motor 4 kW, lifting and lowering motor 2 kW. The machine has been overhauled, the conveyor belt is in very good condition. New graphite shoe. The machine is equipped with two bottom aggregates: the first is a rubber contact roller, the second is a combi system with a graphite pad. Working sanding width is 630 mm. Two feed speeds: slow and fast. Sanding belt length is 1900 mm. Pneumatic oscillation. Pneumatic belt tensioning. Sanding belt speed: 18 m/s. Conveyor belt speed: 9/20 m/min. Number of sanding shoes: 1. CE conformity declaration. Total rated power: 21 kW. Maximum workpiece height: 160 mm. The machine has two lower working rollers. The conveyor belt is positioned above the workpiece. Cgjdpfxjfxpbms Afnsp

Stanje: zelo dobro (rabljeno), skupna širina: 1.300 mm, skupna dolžina: 3.500 mm, skupna masa: 7.000 kg, obratovalni tlak: 300 letvica, transportna širina: 1.600 mm, transportna višina: 2.350 mm, transportna dolžina: 4.350 mm, Polična stiskalnica za furniranje Simimpiantin 3500×1300 Dolžina police: 3500 mm Širina police: 1300 mm Dva nalaga Stiskalnica z 8 cilindri Police ogrevane z vodo iz centralnega ogrevanja Maksimalni delovni tlak: 300 bar Premer batov: 80 mm Teža stroja: 7000 kg Cgodpfxsxxpgbs Afnep Mere stroja: 435x160x235 cm (V)

Stanje: rabljeno, Leto izdelave: 2003, Funkcionalnost: omejena funkcionalnost, številka stroja/vozila: 0 278 06 1192, širina folije: 700 mm, premer valja: 700 mm, Used roll slitting machine, make: Friz. One set of knives has been resharpened. The machine is pre-owned and is sold without warranty. Cgjdev Radxepfx Afnsp Inspection is possible and encouraged. Loading facilities available.

Stanje: rabljeno, Leto izdelave: 1990, No. 04502 Veneer Press Ott JU 2511/70 Used, year of manufacture: 1990 Electrohydraulic, approx. 15 kW Aluminium heating plates 2550 x 1100 mm (L x W) Electrical heating 4 hydraulic cylinders, each 80 mm diameter Total pressing force: 70 tons Specific pressing force: 2.5 – 3.5 kg/cm² Opening width: 400 mm Push-button control for open – close – stop Pressure monitoring with automatic adjustment Adjustable limit switch for specified opening width HAWE pump Safety pull cord Includes electrical cable and 32 A plug Includes electrical diagrams, operating manual as PDF file Transport dimensions approx. 2900 x 1400 x 2000 mm (L x W x H) Weight approx. 3000 kg To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sale in as-is condition Technical specifications, condition description, year of manufacture, and scope of delivery according to manufacturer’s brochure and/or previous owner, without guarantee Subject to prior sale No warranty is given for used machines, sale is strictly “as inspected” Payment terms: Prices plus statutory VAT, payment before collection or shipping Csdpexwp S Iofx Afnjgp Delivery terms: ex stock

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2003, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: W230-028, stiskalna sila: 80 t, trajanje garancije: 24 meseci, pritisk: 250 letvica, moč: 45 kW (61,18 KM), leto zadnje generalne obnove: 2024, Oprema: dokumentacija / priročnik, This fully refurbished baler is being sold by Bollegraaf Recycling Solutions. Cgodpetvat Tofx Afnep It concerns a HBC80 baler (45kW) equipped with vertical tying. This baler has already been completely refurbished in our overhaul workshop. The refurbishment was carried out in accordance with the strict Bollegraaf OEM Refurbishment Guidelines. After refurbishment, this baler is sold including a 2-year warranty. The press is supplied with the following options: * support stands, * intermediate hopper, * bale exit chute, * wire spool platforms