Linija za brušenje masivnega lesa

HOMAG SANDTEQ W-700+B-700

Working height: 900 mm
Working width: 1,350 mm
Abrasive belt exchange side: left
Workpiece thickness: 3 – 160 mm
Frequency-controlled feed speed: 4 – 20 m/min

Abrasive belt dimensions: 2,620 x 1,350 – 1,380 mm
Adjustable abrasive belt blow-off device, 5-stage adjustable

WRD WORKPIECE CLEANING ROTOR
Workpiece cleaning unit with 16 rotating nozzles

MOBILE CONTROL TERMINAL
powerControl with powerTouch

SST SOFT STARTER
Inrush currents are limited to prevent voltage drops

GWRD BELT CLEANING PROGRAM
After activating the program, the machine automatically adjusts to 10 mm workpiece thickness and the blow-off rotors are activated. After complete cleaning of the feed belt, the machine returns to the initial setting.

AAT EXTRACTION SLIDE VALVE CONTROL
Control of extraction slide valves via the terminal (24 Volt DC, slide valves not included)

UPS EMERGENCY POWER SUPPLY FOR BELT CONTROL 1-3 PC
Emergency power supply for the abrasive belt oscillation in case of power failure

Configuration consists of:
SANDTEQ W-700, PROFI SWB735/RRE – bottom sanding
Wide belt sander with three sanding units for processing wood or wood-based workpiece surfaces. The machine is prepared to accommodate up to two auxiliary units, such as cleaning brushes, finishing or structuring brushes, and rotating cleaning nozzles.

Units:
I. R-UNIT
Sanding unit with automatically adjustable contact roller,
profiled steel roller, 240 mm diameter,
with grit compensation
Drive motor: 37 kW
Abrasive belt speed: 25 m/s

- Automatic locking of the sanding unit for fast belt change and increased process reliability
- Abrasive belt drives with electronic, wear-free brake
- Optical, contactless abrasive belt control
- Pneumatic abrasive belt tensioning with integrated abrasive belt edge compensation

II. R-UNIT
Sanding unit with automatically adjustable contact roller,
rubber-coated roller, 240 mm diameter
Rubber hardness: 85° Shore
With grit compensation
Drive motor: 30 kW
Abrasive belt speed: 18 m/s

III. E-UNIT
Sanding unit prepared for a pressure beam

- Automatic locking of the sanding units for fast belt change and increased process reliability
- Abrasive belt drives with electronic, wear-free brake
- Optical, contactless abrasive belt control
- Pneumatic abrasive belt tensioning with integrated abrasive belt edge compensation
- Protected storage on the machine for additional sanding inserts

Drive motor: 22 kW
Abrasive belt speed: 2 – 18 m/s
Torque-dependent standby mode to reduce energy consumption.

ACP PNEUMATICALLY SUPPORTED PRESSURE BEAM
- Adjustable sanding pressure via pressure regulator
- Workpiece-controlled engagement and disengagement at the leading and trailing workpiece edge
- Various sanding inserts, 80 mm wide with different felt hardness grades

Machine dimensions L x W x H: 3,900 x 2,100 x 2,000 mm
Machine weight approx. 7,500 kg

SANDTEQ B-700, PROFI SWT735/RRE – top sanding
Wide belt sander with three sanding units for processing wood or wood-based workpiece surfaces
Units as above, with the addition of:

FBM FINISHING BRUSH
Brush unit with finishing brush
Brush material: horsehair
Diameter: 130 mm
Drive motor: 0.75 kW
Nkjdpfxsyw Ndmj Advsw

Machine dimensions L x W x H: 2,995 x 2,100 x 2,255 – 2,415 mm
Machine weight approx. 6,500 kg

Oglas je bil avtomatsko preveden. Možne so napake pri prevodu.