Drobilnik z dvema gredema

Heger LION 300 B1200

Leto izdelave: 2003, Stanje: delavnici obnovljeno (rabljeno), Stock number: 2651 1 used, partially overhauled in 2023, underwater pelletizing system Throughput up to approx. 450 kg/h depending on material, consisting of: Type BKG (Nordson) Start-up valve with hydraulic unit Granulator type A300 incl. die plate and cutter bar, drive 4.4 kW By-pass system TVE 1000 ED pellet dryer, drive 4 kW incl. Agglomerate catcher Temperature-controlled water system with Water tank 200 liters, installed heating capacity 9 kW Water pump 2.2 kW with 15 m³/h Heat exchanger Control system Further UWG pelletizers available ex works Wuppertal (Gala, BKG Nordson, Econ) Rbedpfx Ajiyyf Iod Tet Available from stock Wuppertal: Complete compounding and pelletizing lines with single-screw or twin-screw extruders.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2007, obratovalne ure: 21.676 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 78 t, širina odprtine za polnjenje: 750 mm, dolžina polnilne odprtine: 1.500 mm, širina bale: 1.100 mm, višina bale: 750 mm, teža bale: 600 kg, skupna masa: 25.000 kg, transportna višina: 3.000 mm, kapaciteta rezervoarja za olje: 1.000 l, moč: 55 kW (74,78 KM), lastna masa: 25.000 kg, volumenski pretok: 930 m³/h, obratovalni tlak: 250 letvica, Good day, We are pleased to offer you, on a non-binding basis, a used baler manufactured by Presona AB, model LP 80 VH1. The following technical data has been taken from the manufacturer's operating manual and brochures. We do not assume any liability for their accuracy or completeness. Manufacturer: Presona AB, Sweden Rjdpevgrh Usfx Ad Tebt Model: LP 80 VH1 Year of manufacture: 2007 Total operating hours: 21,676 hours (as of November 2024) Press force (main press): 78 t Specific press force: 95 N/cm² Pre-compression flap force: 28 t Feed opening dimensions: 1,500 x 1,100 mm Fill volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying: 5-fold vertical Hydraulic oil tank capacity: 1,000 L Baler dimensions (assembled with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight (baler) approx. 25 t Note: The machine was used in a recycling operation for compacting paper, cardboard, and films. The baler is in good condition, will remain in operation until January 2025, and can be inspected by prior arrangement. We would be pleased if this machine is of interest to you. Your service team at Mertens & Frowein GmbH

Leto izdelave: 2010, Stanje: dober (rabljeno), 2 SICON shredders Year: 2010 Electrical cabinet is missing Price: €15,000 each 4 densimetric tables: €8,000 each Redpfoiz Tm Ijx Ad Tebt

Stanje: generalkompletno obnovljen (rabljeno), Funkcionalnost: popolnoma funkcionalen, premer rotorja: 400 mm, dolžina rotorja: 1.000 mm, moč: 37 kW (50,31 KM), največja hitrost vrtenja: 100 obr/min, delovna širina: 1.000 mm, Single-shaft shredder OVERHAULED Rotor diameter: 400 mm Working width: 1,000 mm Drive: 37 kW Rbodpfevnl Ukox Ad Tot Hydraulics: 1.5 kW Rotor knives: 48 pcs Stator knives: 4 pcs – adjustable

Stanje: novo, Leto izdelave: 2025, Funkcionalnost: popolnoma funkcionalen, We deliver the machines wherever you require, and install them upon request by prior arrangement. Rbedpfx Adot Iw Hue Tjt Optional: Stainless steel discharge element, stainless steel storage silo, blower, and approximately 3 meters of piping. Grinding mill 800 series, 22 kW or 37 kW 3 x 2 blade set configuration. Bwj3E79Mpn 2 x stators Screen deck as per your request with Variable Frequency Drive, optional Product discharge and storage available in various configurations at highly competitive prices when combined. Motor power can be adjusted. Other modifications are negotiable, such as rotor adaptations (e.g., 5 rows of blades or heavy-duty version). Delivery/timeframe to be coordinated. Please call or email us to discuss or if you have any questions. Kindly respond with your name, company name, and correct phone number. Without this information, RSS Recycling Shredders and Solutions (Netherlands) will not be able to respond.

Stanje: rabljeno, Leto izdelave: 2017, Mono-rotor shredder 800 series, 2017 used, operational. Blades and screen in good condition, ready for use. Including control cabinet. 30 kW, 40 mm screen, other sizes available on request, rotor length 800 mm, hopper dimensions 800 x 1200 x 950 mm (depth). Machine is immediately available and can be inspected. Rsdpfx Ajwcp H Sod Tobt

Leto izdelave: 2017, Stanje: pripravljen za uporabo (rabljen), Material throughput: LDPE: 110 kg/h, PA6.0/LDPE/EVOH: 150 kg/h, PP/PA6.0/LDPE/EVOH: 135 kg/h, PA6.0/LDPE: 120 kg/h, EVA/LDPE: 150 kg/h. Rated power: 77 kW, PCU power: 30 kW, extruder power: 18.5 kW, motor power: 10.7 kW, heating zones: 1, heating capacity: 12 kW. Documentation available. On-site inspection is possible. Rbjdpswty Hkofx Ad Tst

Stanje: rabljeno, Leto izdelave: 2018, premer rotorja: 368 mm, širina rotorja: 1.500 mm, No. 10027 Single-Shaft Shredder / Shredder AMIS / WEIMA WT 15 Used, year of manufacture 2018, approx. 250 operating hours According to our customer, the machine is fully functional and can be inspected and tested on site Single-shaft shredder for cables, plastics & recycling Feed opening: 1500 x 1160 mm (LxW) Rotor width: 1500 mm Rotor diameter: 368 mm Rotor speed: approx. 90 rpm Motor power: 90 kW Throughput: approx. 5 tons per hour (depending on material) Total plant output: 99 kW Current consumption: 210 A Voltage: 400 V / 50 Hz PLC control: Siemens SIMATIC Built-in screen with hole diameter 20 mm Replacement screen with hole diameter 50 mm The high-performance shredder of the WT series is ideally suited for processing a wide range of plastics – especially difficult, flexible materials such as films, filaments, big bags, tapes, carpets, textiles, foams, as well as all loose and non-bulky residual materials. The WING-RAM swing arm ensures reliable feeding even of contaminated or moist material. Incl. angled conveyor belt / discharge belt AMIS FB 7000 x 1500 x 580 / year of manufacture 2018 / 1.5 kW Incl. AMIS magnetic separator Installation dimensions approx. 9000 x 3500 x 3950 mm (LxWxH) Transport dimensions (single-shaft shredder) approx. 3000 x 2700 x 3200 mm (LxWxH) Weight: approx. 12,500 kg Sale on behalf of customer, ex location near 69123 Heidelberg, without dismantling, transport and assembly Dismantling, transport and loading by us optionally available Errors in description and price excepted To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sale is as-is Technical data, condition description, year of manufacture and scope of delivery as per manufacturer’s brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: "purchased as inspected" Images and videos are for illustration purposes only and do not represent the actual scope of delivery Payment terms: Prices plus statutory VAT, payment before collection or shipping Delivery terms: ex location Rbsdpfexwdiujx Ad Tot

Stanje: novo, Leto izdelave: 2025, We offer customized conveyor belt solutions, whether chain belt conveyors, plate conveyors, or sliding belt conveyors, to feed baling presses, shredders, or as extensions for roll cutting systems. Rsdpfxjq A S Evs Ad Tsbt Manufactured according to customer requirements, this is an example offer.

Leto izdelave: 2022, Stanje: pripravljen za uporabo (rabljen), Recycling plant complete with regranulation unit, conveyor belt, roll feed, granulate dosing unit, twin-screw feed system, and bagging station. 1) Regranulation unit components: Piovan loading system, backflush filter, extraction system, process water tank, hot-cut pelletizer, pellet dewatering screen, pump station, pellet weigher, pellet centrifugal dryer, pellet conveying system, filling station, and a swiveling side wall for PCU hood. Throughput for MDPE, LDPE: 650–725 kg/h. PCU motor: 132 kW. Weight: 12,680 kg. Extraction air capacity: max. 3,000 m³/h. Weight: 174 kg. Process water tank volume: approx. 860 l. Backflush filter screen diameter: 215 mm; number of screen packs: 4. Hot-cut pelletizer: 4 knives; knife head speed: 1,420 rpm. Pellet dewatering screen size: 1900 × 700 mm. Oversize separation: below 20 mm. Tank volume: 470 l. Pellet centrifugal dryer: motor power 7.5 kW. Pellet conveying air volume: max. 1,900 m³/h. Length (without Big Bag station): approx. 11,642 mm; width: approx. 8,000 mm. 2) Conveyor belt with hopper, level sensor, and dual-layer metal detector. Weight: approx. 950 kg. Belt dimensions: 7,000 × 1,100 mm, with cleats. Metal detector coil passage: 1,300 × 400 mm; detection: all metals. Sensitivity: Fe = M6 nut, stainless (V2A) = M10 nut. Technology: digital; alarms: visual and audible. 3) Roll feed system: feed cross-section 450 × 150 mm. Motor power: 1 × 1.5 kW. Max. feed speed: 20 m/min. Rbedpsx Dm Dhefx Ad Tjt 4) Granulate dosing unit: gravimetric operation. Bulk density: 0.6 kg/dm³. Dosing range: 4–40 kg/h. 5) Twin-screw feed system: bulk density 0.6 kg/dm³; max. output: 100 kg/h; screw diameter: 40 mm. 6) Bagging station frame: for 2 Big Bags, with pneumatic diverter and level sensor. Total operating hours: 6,400 h. Complete documentation included; additional spare parts available on request. On-site inspection possible.