Odprta polprikolica

Fliegl 3-Achs Plateau SDS 420 Scandic Spezial

Chassis semi low loader for haulage
Fine-grained steel welded construction in reinforced Scandic design, fifth wheel plate with replaceable 2" kingpin
Outer frame in low loader design:
7 pairs of lashing mushrooms recessed at the top and side in the outer frame, each rated for 10 t
10 pairs of combined stake pockets with lashing rings (bolted), each rated for 5 t, recessed in outer frame, approx. 72 x 42 mm inner dimensions
Outer frame with "Load-Lock profile" for fitting tensioning straps, approx. one hole every 400mm
24 t, 2-speed landing leg with single-sided operation
Free swing radius to landing foot approx. 2,500 mm, landing foot width approx. 2,600 mm
Extension ladder at rear
2 wheel chocks with holders
Side underrun protection, aluminium
Rear underrun protection, galvanized steel
Spray flaps at the rear over entire width
Quarter mudguards in front of and behind axle assembly
With antispray mudflap only on rearmost axle
2 plastic toolboxes, w=600 / h=425 / d=460 mm, lockable
In front of axles, 1x left, 1x right
1 storage box, full width, closed, beneath loading floor, approx. w=450 mm/h=400 mm/d=2,460 mm, mounted directly in front of axles
3 tie-down/stake rails with 4 pairs of locking cut-outs, recessed transversely in floor over total width up to outer frame (max. usable internal width between outer stanchions approx. 1,782 mm), approx. 80 mm high. With cut-outs at top and bottom for lashing and fitting stakes 80 x 80 mm. Bottom with angled plate as stop, half open downward. Combined design for 2 x 20 ft or 1 x 40 ft container, 4 pairs of container lock adapters
10 combined plug-in stakes with cut-out at bottom, w=80/ d=50/ l=1,200 mm
6 plug-in stakes w=80/ d=80/ l=1,200 mm, hot-dip galvanized
Axles and Suspension
BPW disc brake axles with 430 mm disc diameter
Air suspension
1st axle auto lift, additionally electrically operable from tractor, including forced lowering and start aid
Braking system
2-line compressed air braking system
Spring-type parking brake
2 non-interchangeable couplings at front
24V EBS, electronic braking system with EBS socket at front
Note: Towed vehicle may only be towed by towing vehicles that guarantee proper functioning of ABS!
with raise & lower valve + auto-reset function
Vehicle Stability Control System
Axle load detection via EBS CAN bus signal, display in driver’s cab
Wheels and Tyres
385/65 R22.5"
Steel rims
"TPMS" tyre pressure monitoring system according to ECE R 141, display via towing vehicle, through EBS
Electrics
24 Volt, multi-chamber lamps, side yellow LED marker lights
Side yellow LED marker lights linked with indicator “flashing side markers”
2 white LED position lights at front
2 white/red lane marker lights at rear
2 x 7-pin and 1 x 15-pin non-interchangeable sockets at front
2 additional LED work lights, at rear
1 LED beacon with mounting bracket
2 pairs of LED illuminated warning signs, extendable to 3,000 mm
2 additional LED worklights, top of front wall
Additional 7-pin socket in rear underrun guard
Floor
Slip-resistant screen printing panels approx. 30 mm thick, for high point load, suitable for forklift wheel loads up to max. 7,900 kg
"Premium floor sealing", circumferentially sealed joints
Bdedpozbbpuefx Acmsc
Front wall / corner posts
25 mm aluminium hollow profile, 1,350 mm high, corner posts steel, volume design
Front wall additionally lined inside with 1,250 mm high phenolic plywood
"Crash Blocker", bottom inside at approx. 140 mm high, with steel impact protection

Oglas je bil avtomatsko preveden. Možne so napake pri prevodu.