Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE Multimax Satteltieflader (1+2) - nachlaufgelenkt

Our complete vehicle inventory, including vehicles available immediately or at short notice, can be found on our website.

Excerpt from the equipment. Full equipment details available on request.

GOOSENECK:
* Gooseneck in SNT design to optimize load bed length, approx. 3,700 mm long, with rear taper approx. 1,000 mm x 10°
* For tractor units: 4 x 2, 6 x 2, and 6 x 4
* Steel front bulkhead, removable, approx. 400 mm high
* ASPÖCK-UNIBOX
* 3 kW electric-hydraulic unit for hydraulic operations, excluding hydraulic winches
* Approx. 40 mm thick hardwood cover above the gooseneck
* 2-inch kingpin
* Guide plate from the gooseneck for the fifth-wheel plate, approx. 500 mm wide
* Receptacle at the rear of the gooseneck for aluminum drive-on ramps
* Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917)
* 4 wheel chocks with holders in front of the bulkhead
* 1 pair of stake pockets embedded in the gooseneck, for plug-in stakes approx. 100 x 50 mm (inner chassis rail)

EQUIPMENT:
* Load bed approx. 8,800 mm long, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10°
* Recess in the load bed including the rear slope to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H)
* Pneumatic locking with conical locking bolts and reinforced locking positions, with protected supply lines inside the extendable beams, automatically adapting to the respective load bed length
* TPMS tire pressure monitoring system according to ECE R 141
* BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle steering-following
* 3rd axle with electromagnetic reverse lock, activating via reverse gear or manually
* Technical axle load: 12,000 kg each, air suspension with lift and lower valve
Iodpfxjy Auh Is Aa Ujar
* 235/75 R 17.5 3PMSF twin tires. Make at our discretion
* Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg
* Continuous and between-axle interrupted approx. 50 mm hardwood planking on load bed (increasing coefficient of friction)
* 1 cross table, approx. 300 mm wide, for the extendable tube with large cross-section; cross table with offset load bed and extendable mounting rails for aluminum bridging elements
* Load bed locking with conically welded locking profiles every approx. 250 mm, including pretensioning plate
* 1 pair of lashing rings on front crossbeam (LC 10,000 daN)
* 9 pairs of recessed lashing rings in the outer frame of the load bed, foldable outwards (LC 10,000 daN)
* 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck crossbeam, approx. 700 x 410 mm (W x D)
* Wheel recesses with approx. 15 x 15 mm square climbing strips and widened sections at the lower area (if vehicle is fitted with extendable widenings)
* 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the load bed between 1st and 2nd axle
* Wheel recesses with approx. 15 x 15 mm square climbing strips and widenings in lower area
* Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, can also be used as widening planks (if vehicle is fitted with extendable widenings)
* Aluminum elements lockable on the extension beams of the widenings
* 1 pair of mechanical rear supports
* 1st axle with traction aid
* Sandblasted and painted in single color according to RAL code

Oglas je bil avtomatsko preveden. Možne so napake pri prevodu.