Avtomatski rezalnik stebrov

CORMAK HR500SA przecinarka taśmowa do metalu

Stanje: dober (rabljeno), Leto izdelave: 1972, Swing diameter over bed 330 mm Swing diameter over cross slide 200 mm Turning length 800 mm Total connected load 3 kW Machine weight approx. 800 kg Space requirement approx. 1.9 x 0.7 x 1.2 m Spindle speed range 24-2800 rpm Accessories: * 2 lathe chucks with spare jaws * 5 Multifix tool holders * Change gear set * Various centers and accessories Fsdpfswwl Izsx Afljft

Stanje: novo, Leto izdelave: 2025, Patented mitre system Continuously adjustable cutting speed Hydraulic feed control Hydraulic lifting and lowering of the saw frame Hydraulic material clamping Powerful frequency-controlled saw band drive Swivel range 30° right / 45° left Ffodpfx Afeh S Nxpslet Cutting capacity in mm 45° left round 300, flat 300 x 300 90° round 410, flat 620 x 410 45° right round 360, flat 420 x 360 30° right round 300, flat 300 x 300 Remnant piece length without bundle clamping 60mm Recommended options: Micro-spray system Laser line Clamping pressure regulator Powered chip brush Manual lifting roller Setup elements

Stanje: novo, Cutting diameter round: 900 mm Cutting diameter square: 900 mm Cutting diameter flat: 900x900 mm Saw band length: 9300 x 67 x 1.1 mm Table height: 790 mm Band speed: 14 - 60 m/min Total power requirement: 11 kW Machine weight approx.: 8.45 t Dimensions (L x W x H): 4,485 x 1.68 x 3.15 m The semi-automatic, hydraulic saws of the X-tech line offer top-tier sawing technology and maximum performance when cutting specialty steels. - The electro-welded machine frame and the steel saw frame meet all cutting requirements and eliminate vibrations and noise. - The chip conveyor is hydraulically driven and the speed is adjustable. - All machine motions (saw frame, vice, feed, saw band guides) are enabled by modern linear guides with high static and dynamic load capacity, guaranteeing very low sliding friction. - Another key feature is the material positioning rollers, which are powered by a hydraulic motor. These move at a right angle to the material, allowing for optimal clamping. Ffedpfofg E Hpex Aflot - Thanks to the saw band position height control, the operator can position the band close to the material’s upper edge. After cutting, the band automatically returns to the previous position; alternatively, the 'remain' option in the lower position can be selected. During the cutting cycle, the software compares cutting force with preset values and can stop the sawing system in case of irregularities. - The saw band is cleaned by two adjustable steel brushes, which are hydraulically driven. - The hydraulic unit, including filter and manometer, ensures especially smooth operation at constant pressure. - Precision ground carbide inserts clamp the saw band, complete with lateral, hardened, and adjustable guide rollers. The adjustable band guide automatically moves as close as possible to the material. - The saw band is tensioned by a hydraulic cylinder, controlled by the machine software. Tension is automatically released after a preset time when the machine is idle or after a cycle is completed. - Automatic version with CNC control available for the X-TECH 900 / 1200 models with a feed length of 500 mm for high production series. - The material is supported by a table with seven rollers, powered by a hydraulic orbital motor, allowing precise material positioning even under maximum load. - All guided motions are facilitated by four ball circulation guides with high static and dynamic load capacities; significantly reduced feed friction. Hardened and ground prismatic guides. Price on request.

Stanje: novo, AGRE ALUP ALLEGRO 14+ 13 270 Speed-controlled. Space-saving. Cost-effective. Efficient 1:1 direct drive. Easy operation. Low energy consumption. High performance. Suitable for a wide range of applications. Outstanding compressed air quality. Cyclone separator and refrigerated dryer integrated. Detailed Features: Compression Concept: Oil-lubricated screw compressor Cooling: Air-cooled design Drive: High-frequency motor with 1:1 direct drive Control: Speed-adjusted via frequency inverter Controller: Graphic control unit C55DD Refrigerated Dryer: Integrated, refrigerant R513A Filtration: Includes cyclone separator Tank: Horizontal, painted Fjdpfoixt I Hsx Afloft Performance Data: Volume flow at 7.0 bar operating pressure: 0.26–2.26 m³/min Operating pressure min./max.: 5.0 / 12.5 bar Total power consumption at 10.0 bar / full load: 16.2 kW Motor rated power: 15 kW Oil volume: 5.2 liters Dimensions and Weight: L x W x H: 1655 x 655 x 1550 mm Weight: 400 kg Compressed air outlet: G 3/4'' Compressed air tank capacity: 270 liters

Stanje: novo, Cutting capacity at 90° (round): 350 mm Cutting capacity at 90° (square): 330 mm Cutting capacity at 90° (rectangle): 450 x 320 mm Saw band length: 4250 x 34 x 1.1 mm Band speed: 40 + 80 m/min Table height: 845 mm Saw blade width: 34 mm Total power requirement: 2.2 kW Machine weight: approx. 0.985 t Space requirements: approx. 1.4 x 2.0 x 2.2 m Double mitre band saw, hydraulic semi-automatic, DGS 350/450 HA-I • Mitre cuts left & right up to 60° without machine conversion • 34 mm saw blade width • Large, ball-bearing supported, rotary worktable • Saw blade guides adjustable over extra-wide linear rails • Heavy-duty, robust gearbox • Large-area clamping plates • Infeed and outfeed roller • Removable chip tray (for cleaning) • Free-standing, safe, ergonomic control panel • Storage space for blades and consumables Fjdpfxofgyics Afljft • Cutting pressure control and feed rate regulator • Fully hydraulic vice • Quick clamping (front loading) • Material height sensor (automatic cut start detection) Semi-automatic operation: 1. Clamp material 2. Start saw 3. Rapid descent to start of material or direct cutting for series cuts 4. Switch off saw band 5. Raise frame just above the material 6. Open vice Optimal, material-independent cutting results through fine adjustment of the saw frame via: * Pressure control valve (cutting force) * Feed rate control valve (cutting speed) * Clearly arranged selector switch with pictograms for intuitive operation

Stanje: dober (rabljeno), Leto izdelave: 1999, Deli, prikazani z roko, niso vključeni. Ffedpfx Afewbz Tuolet

Stanje: novo,

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2016, Cleaning System Type W 60 C Machine body, internal piping system, control cabinet, and washing basket made of stainless steel Combination machine – rotating table system with removable tilting device and small parts basket - Basket diameter (rotating table washing basket): 600 mm - Usable internal height: 370 mm - Basket load capacity (rotating table washing basket): 100 kg - Usable internal height: 530 mm - Small parts basket dimensions: 375 x 220 x 200 mm - Mesh size: 12 mm - Basket load capacity (small parts basket): 20 kg Full stainless steel construction Pump(s) and external piping/fittings version Suitable for operation with liquids with a density of 1.3, featuring a reinforced pump with frequency converter Chip/particle filter with bath cover plate ECO rinse (minimized rinse loss) for minimal water consumption Water supply from operator's mains with machine-side hot water supply Hot air drying 1 x 4 kW Oil skimmer Ffodpfjq Ewgksx Aflot Discharge device/floor flushing with pump and piping system in stainless steel

Stanje: dober (rabljeno), Spectro CIROS CCD Water Analysis Device - Height: 105 cm Fedpfx Afofiqn Ujlsft - Width: 150 cm - Depth: 75 cm Good condition, fully functional. Can be inspected and tested on site. International shipping available. Inspection: Please note that, to avoid any misunderstandings, the item can be viewed and tested under power before purchase. If you have any questions, please ask them prior to purchasing to prevent any uncertainties. For general inquiries or to schedule a viewing appointment, I am always available at the phone number listed below. Errors in description and prior sale excepted. VAT will be shown separately on my invoices. Shipping via freight forwarder.

Stanje: rabljeno, Leto izdelave: 2018, DEMAG mostno dvigalo – Nosilnost 16 ton – Letnik 2018 Ffodpjxb D Nvefx Aflot Proizvajalec DEMAG Cranes & Components GmbH – Nemčija Tip Industrijsko motorizirano mostno dvigalo – enojni ali dvojni nosilec Industrijska uporaba Za težka dviganja v jeklarnah, proizvodnih delavnicah, kotlarstvih, splošni strojni obdelavi in logističnih skladiščih Glavne tehnične specifikacije: - Nazivna nosilnost: 16 ton (16.000 kg) - Leto izdelave: 2018 - Proizvajalec: DEMAG – globalni vodilni v industrijskem dviganju - Motorizirano premikanje po tirnicah - Električni vitel z jeklenico (DEMAG standard, velika nosilnost) - Napajanje: industrijski trifazni tok - Upravljanje: obesek ali radijsko daljinsko upravljanje (odvisno od konfiguracije) - Stanje: rabljeno – nedavno, robustna zasnova 🧩 Uporaba stroja DEMAG mostno dvigalo z nosilnostjo 16T je zasnovano za težka dviganja v zahtevnih industrijskih okoljih. Velika nosilnost ter sodobna konstrukcija zagotavljata učinkovitost, varnost in dolgo življenjsko dobo. ⚙️ Značilnosti / prednosti - Srednje visoka nosilnost (16T) za težje industrijske procese - Sodobna izdelava (2018) skladna z aktualnimi varnostnimi standardi - Vgrajeni DEMAG vitel in električni sistemi - Možnost integracije avtomatizacije in daljinskega upravljanja