Zazidalni stroji

Comec FFM/LX

Stanje: rabljeno, Leto izdelave: 2001, Wood processing dimensions: Infeed lengths min/max: 500 - 6500 mm Full optimization up to max: 1500 mm Infeed widths min/max: 40 - 300 mm Infeed thicknesses min/max: 15 - 120 mm Max. wood cross-sections: 300 x 40 mm or 200 x 120 mm Fixed lengths after saw min: 510 – 2800 mm Special application: Cutting blocks, min/max length: 100 – 200 mm (Note: Multiple block lengths during sorting; blocks are conveyed to the end of the sorting line and fall into customer-supplied mesh boxes) Cutting/trim tolerance: +/- 0.8 – 1.5 mm (depending on timber quality with minimal resin content and uniform surface. Tolerance up to 1 m fixed length; maximum tolerance for longer parts up to 2.5 m). Thickness tolerance: +/- 3 mm Bcsdpfxsw Sy T Ho Ag Tow Wood curvature in all directions: max. 10 mm per meter length Wood species: Softwood or hardwood System performance: Feed speed, steplessly adjustable up to max. 230 m/min Cutting cycle: 0.6 – 1 s To determine actual daily output, an efficiency factor dependent on the customer’s production conditions must be applied. Working height infeed and saw: 900 mm (to be placed on customer-side platform; saw requires concrete base) Sorting working height: 2000 mm Connection data: Total electrical connection load: approx. 18 kW Operating voltage: 380 Volt / 50 Hz Voltage fluctuations max. 5 % Air consumption: approx. 1200 NL/min Operating pressure: approx. 8 bar Extraction speed: approx. 30 m/s Paint finish: pebble grey RAL 7032 and blue NCS 5030-R 80 B POSITION OVERVIEW: Pos. 1: Infeed and marking station with 1 adjustable side support table, 1 table as stop edge Pos. 2: Support roller without drive, front-facing sheets table for easier loading Pos. 3: Length measuring station with built-in fluorescence camera to detect error markings Pos. 4: Automatic, contactless width measurement Pos. 5: Optimizing cross-cut saw OptiCut 304 – right-hand version with integrated waste chute, incl. equipment package for large wood cross-sections Graphic-capable input terminal (16 x 40 characters, numeric keypad) with software package for optimization and system control Available for processing: - max. 16 product groups - max. 8 grades per product group - max. 200 fixed lengths per product group Pos. 6: Outfeed conveyor belt as sorting station with drive unit, length 7500 mm Pos. 7: 2 ejectors mounted on outfeed conveyor Location: Nattheim

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2022, obratovalne ure: 500 h, Funkcionalnost: popolnoma funkcionalen, Drying Paternoster for Finger-Jointed Boards Consisting of: - Transfer chain after finger jointing press, foldable - Drying paternoster approx. 7 m, suitable for board lengths up to 6 m - Cut-off and zeroing saw - Conveyor belt for residual wood disposal - Stacking system - Batten magazine is not for sale - Package cross conveyor Bjdpfxewclkyj Ag Tscw The machine is in very good condition, very little operating time. The machine is still assembled but immediately available.

Stanje: potreben popravila (rabljeno), Leto izdelave: 1999, Funkcionalnost: nefunkcionalno, Machines for restoration Bjdpfx Ajlxqk Reg Tjcw

Stanje: dober (rabljeno), Leto izdelave: 2001, Prodajam 3-osni CNC obdelovalni center HOLZ-HER UNI-MASTER 7226 s prečnim delovnim mizo, letnik 2001. Konfiguracija: Glavno vreteno za 3 osi, popolnoma obnovljeno / vodno hlajeno Magazin za orodja za 6 HSK63 mest na glavi 1x utorna žaga v X-smeri Vrtalna glava s 16+4 vrtalnimi vreteni Uporabna delovna površina 3100x1360 mm 2 delovni območji, 4 vpenjalna območja Avtomatski sistem centralnega mazanja Holzher programska oprema z navodili za uporabo Črpalka SIEMENS ELMO-L S22 2,35 kW Dodatni vakuum za šablonska dela ali dodatne vpenjalne naprave Bcsdpji U Dxuofx Ag Tsw Dobro stanje. Na voljo takoj iz zaloge.

Stanje: dober (rabljeno), Leto izdelave: 2008, Granulator La Meccanica CLM 800 POR Bcodpewdawqjfx Ag Tjw The machine does not have doors It was used for processing wood shavings

Stanje: rabljeno, številka stroja/vozila: 007350, Working area X-axis: 4000 mm Working area Y-axis: 1400 mm Working table: With vacuum console supports Bcodpfowcyd Isx Ag Tow Main spindle power: 15 kW Number of controlled axes: 4 axes Number of drilling spindles: 30 Number of tool positions: 28

Leto izdelave: 1998, Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, Very sturdy roller conveyor with hydraulic lift and lower cross conveyor. Section 1: Length 7,100 mm. Roller length 2,000 mm. Roller diameter 220 mm. Bedot Hg Huopfx Ag Tocw Construction height 1,000 mm. Integrated hydraulic lift and lower cross conveyor with 4 chain strands. Spacings: 1,500 - 1,300 - 1,000 mm. Completely sheet metal covered. Hydraulic supporting idler rollers. Driven by a geared motor. New bearings. Section 2: Length 7,200 mm. Roller length 1,600 mm. Conveyor length 6,100 mm. Built-in hydraulic lift and lower cross conveyor with 6 chain strands. Cantilevered design allows workpieces to be transferred under the roller conveyor to the left or right. Completely sheet metal covered. Including hydraulic power unit for both roller conveyors.

Stanje: dober (rabljeno), Funkcionalnost: popolnoma funkcionalen, Complete Weinig planing line consisting of: - Package infeed, automatic tilt destacking, baton separator. - Cross conveyor with reject separation. - Conveyor feed to twin band saw, singulation before planing machine infeed. - Throughfeed cross-cut saw, infeed to the planing machine. - Weinig 22 B planing machine with 8 spindles; electronic frequency-controlled feed up to 80 m/min. - In 2023, the planing machine was equipped with a new frequency-controlled feed unit, new table, and new wear plates. - Outfeed from the planing machine; Weinig stacking unit with lath magazine, as well as Almab stacking system. Bcjdpfxowvqvbe Ag Tsw The entire planing line is fully mechanized. Specifications: - Wood length: 2.0 – 6.10 m - Wood thickness: 10 – 120 mm - Wood width: 40 – 220 mm - Package size input: 1.20 x 1.30 m; output: 1.20 x 1.20 m (W x H) Well-maintained system with regular servicing.

Stanje: zelo dobro (rabljeno), Mikser Buhler Batch Mixer, model Speedmix AHLM 4000, w bardzo dobrym stanie. Bcjdpfx Agswf Am Dj Tew

Stanje: rabljeno, No. 3176 WEINIG Hydromat 1000 Planing and Moulding Machine Used, year of manufacture 2007 6 Spindles: bottom-right-left-top-top-bottom Electronic feed: 6 - 60 m/min Working width: 80 - 150 mm Working height: 23 - 65 mm Finished lamella width: 4 - 15 mm Max. number of lamellae: 16 pcs Lamella lengths: 400 - 4000 mm 1st spindle horizontal bottom: Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool circle 125 - 180 mm Bodpfx Agju Agh Sj Tecw 2nd spindle vertical right: Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 80 mm 3rd spindle vertical left: 7.5 kW, 6000 rpm Diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 80 mm Pressure shoe in front of spindle, swiveling, pneumatic roller pressure 4th spindle horizontal top: 15 kW, 6000 rpm, diameter 45 mm Tool circle 112 - 250 mm Max. profile depth 35 mm Axial adjustment 45 mm Divided pressure shoe before upper spindle, adjustable and swiveling, pneumatic 5th spindle horizontal top as saw spindle: Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment reduced to 25 mm Tool circle 112 - 250 mm Max. cutting depth 35 mm Axial adjustment 45 mm Divided pressure shoe before upper spindle, adjustable and swiveling, pneumatic 6th spindle horizontal bottom as saw spindle: Brake motor 30 kW, 5000 rpm Axial adjustment reduced to 25 mm Diameter 45 mm Tool circle 112 - 250 mm Max. cutting depth 35 mm Axial adjustment 45 mm All profiling spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of feed rollers opposite left spindle, axial 35 mm Shortened roller distance opposite right spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in table, lateral pressure roller Automatic Waxilit/lubricant pump Machine with 4-roller outfeed, oscillating shafts extended to 200 mm 2 driven, toothed rollers in outfeed table 2 driven, toothed rollers in machine table Pressure beam ahead of and discharge after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electric height adjustment of upper spindles and feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transport and installation Subject to errors in description and price Transport and loading by us available as an option To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended The sale is made in "as is" condition Technical data, description of condition, year of manufacture and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: "sold as inspected" Pictures and videos are for illustration purposes only and do not represent the actual scope of delivery Terms of payment: prices plus statutory VAT, payment before collection or dispatch Delivery terms: ex site