Obdelovalni center - univerzalni

Bimatec Soraluce FR 9000 II

Stanje: zelo dobro (rabljeno), Manufacturer: HEYLIGENSTAEDT Model: NDC 710 / 1800 Control: R&D MTC3 4-jaw chuck 1400 mm Gbedpfx Anewzh A Ajfol Steady rests: 3 pcs, capacity Ø 100–1050 mm Roller steady: 2 pcs, open type, capacity Ø 1120 mm KNOLL chip conveyor, year 2022 Boring bar Ø 260 x 3500 mm Boring bar Ø 200 x 1500 mm Boring bar Ø 150 x 1100 mm Turning length: 8250 mm Swing over bed Ø: 1400 mm Swing over cross slide Ø: 1120 mm Spindle power: 100 kW Workpiece weight: 16,000 kg Length: 14,000 mm Width: 3,500 mm Height: 2,900 mm Weight: 32,000 kg

Stanje: rabljeno, Clamping Plate – Table of a Long Planer Machine – Table Width / Clamping Width: 1845 mm Table Length / Clamping Length: 5505 mm 7 longitudinal T-slots for T-slot nuts: M30 T-slot spacing: 263 mm Gjdpfx Asbn Amfsnfsbl Total length: 6230 mm Total plate height: 350 mm Weight: 11 t

Stanje: delavnici obnovljeno (rabljeno), Funkcionalnost: popolnoma funkcionalen, premer struženja nad prečnim suportom: 690 mm, izvrtina vretena: 150 mm, premer struženja: 1.040 mm, premer struženja nad zgornjim sanežem: 690 mm, višina središča: 500 mm, širina na sredini: 2.000 mm, največja hitrost vretena: 5.000 obr/min, potovalna razdalja osi X: 160 mm, pomik po osi Z: 380 mm, prehod palice: 55 mm, Centre height: 500 mm Distance between centres: 2,000 mm Maximum turning diameter On cross slide: 690 mm Over bed: 1,040 mm In bed gap: 1,070 mm Bed width (hardened ways): 670 mm Gap length: 480 mm Gap length in front of faceplate: 320 mm CARRIAGE Bed guide length: 1,020 mm Cross slide travel: 640 mm Compound rest travel: 360 mm SPINDLE Spindle nose: ASA 15'' Spindle bore diameter: 150 mm Front bearing size NN: 200/310/82 mm Rear bearing diameter NNU: 190/260/69 mm Internal taper in reduction sleeve: Morse No. 6 Spindle speeds: 24 Speed range: 4 to 800 rpm THREADING Threads: 398 Metric: 0.5 to 224 mm Module: 0.25 to 11 mod. Whitworth: 56 to 1/8 tpi Diametral pitch: 112 to 1/4 DP FEEDS Number: 108 Longitudinal, cross, compound: 0.05 to 22.4 mm/rev Gbodpfjyhhuwex Anfel RAPID TRAVERSE Longitudinal, cross, and compound: 2,500 mm/min Longitudinal return: 5,000 mm/min TAILSTOCK Quill diameter: 130 mm Quill taper: Morse No. 6 Quill stroke: 420 mm STEADY RESTS Steady rest capacity on bed: 140 to 500 mm Steady rest capacity on carriage: 40 to 350 mm PERMISSIBLE LOAD Overhung: approx. 1,500 kg Between centres, without steady: approx. 5,000 kg Between centres, with steady: approx. 6,000 kg Machine weight: approx. 7,800 kg

Stanje: zelo dobro (rabljeno), Leto izdelave: 2011, Steuerungssystem MXS 850 IV Technische Daten: - Max. Umlaufdurchmesser über Bett: 755 mm - Max. Umlaufdurchmesser über Support: 740 mm - Max. Drehdurchmesser: 366 mm - Drehlänge: 785 mm - Verfahrwege: - X-Achse: 260 mm - Y-Achse: 100 ±50 mm - Z-Achse: 795 mm - Eilgang X/Y/Z: 30/20/50 m/min - Spindelleistung: 26/22 kW - Spindeldrehzahl: 4.000 U/min - Stangendurchlass: 80 mm - Futterdurchmesser: 250 mm - Spindelaufnahme: JIS A2-8 - Spindelindexierung: 0,001° - Gegenspindel-Leistung: 11/7,5 kW - Gegenspindel-Drehzahl: 6.000 U/min - Stangendurchlass Gegenspindel: 80 mm - Futterdurchmesser Gegenspindel: 150 mm - Gegenspindelaufnahme: JIS A2-5 - Gegenspindel-Indexierung: 0,001° - Anzahl Werkzeuge im Revolver/angetrieben: 12/12 Stück - Leistung angetriebene Werkzeuge: 5,5 kW - Drehzahl angetriebene Werkzeuge: 6.000 U/min - Maschinengewicht: 6.200 kg - Maschinenabmessungen LxBxH: 4,34 x 2,00 x 2,120 m Godpeyilzhsfx Anfsbl Ausstattung: - Späneförderer - 3-Backenfutter Kitagawa BB-210 im Hauptspindel - Kitagawa B 206 im Gegenspindel - Werkstückfänger - Verschiedene Werkzeughalter - Schnittstellenanschluss für Stangenlader - Synchrongewindeschneiden - Maschine mit 17.800 Betriebsstunden.

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2007, obratovalne ure: 22.605 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.600 mm, širina bale: 1.100 mm, višina bale: 1.100 mm, teža bale: 1.400 kg, skupna masa: 36.000 kg, kapaciteta rezervoarja za olje: 1.300 l, For sale: Fully reconditioned baler with 100 t pressing force, large bale size 1100 x 1100 mm, 75 kW drive power, and 10-fold cross-tying. Technical data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main ram pressing force: 100 t Pre-pressing force: 50 t Operating hours: 22,605 hours Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale size: 1,100 x 1,100 mm Drive power: 75 kW Total connected load: 126 kW Total current draw: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a bulk density of 30 kg/m³: approx. 16 t/hour bulk density of 50 kg/m³: approx. 25 t/hour bulk density of 100 kg/m³: approx. 47 t/hour Bale weights up to 1,400 kg, depending on material and bale length Hydraulic tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Installed baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Gbedpovf E Avofx Anfjl Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Notes: The baler was partially reconditioned, serviced, tested after completion, and stored in our workshop. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment work was performed: - Removal of rust and partial repainting of the press - Complete drainage of hydraulic oil tank, oil and air filters replaced - New hydraulic oil filled - All hydraulic hoses replaced - Main hydraulic cylinder, two pre-press flap cylinders, and compression channel cylinder removed, disassembled, inspected, cylinder tubes honed, all seal kits replaced, and final pressure test conducted - Pre-press flap disassembled with bearings and bearing blocks; first and third arc segments removed and rewelded - Both shaft bearings on the pre-press flap replaced - Upper material guide on pre-press flap frame replaced - Press ram dismantled, inspected, and both front guide rollers replaced - Material guides and wear plates on sides and base of press ram removed and rewelded - Horizontal and vertical needle and tying units dismantled, disassembled, inspected; plastic slide plates, twister shaft bearings, and wire deflector pulleys with bearings in the needle heads replaced - Both bronze slide rails left and right in the frame cover for the press ram replaced - Both wire deflection units left and right, with bale retention clamps completely replaced - Wire feed unit including hydraulic cylinder under needle passages completely renewed - Wire feed tracks in the floor and sidewalls of the press channel welded up and smoothed - General maintenance and servicing carried out according to manufacturer’s specifications - Baler tested in manual and automatic mode after refurbishment, accepted, and stored We accept no liability for the technical data or any potential errors.

Stanje: rabljeno, Leto izdelave: 1988, Maximalni prečnik obrade preko ležišta 2000 mm Prečnik obrade preko nosača / mm Dužina obrade / mm - Tip 1 K 671 320 F3 - Godina proizvodnje 1988 (prva instalacija 1998) - Dužina obrade 10.000 mm - Prečnik obrade preko ležišta 2.000 mm (modifikovan) - Prečnik planske ploče 1.950 mm - Opseg stezanja planske ploče 400 - 1.350 mm Gedpfx Aexn Tz Ijnfsbl - Brzine obrtanja 1,00 - 140 o/min - Obrtni moment 125.000 Nm - Maksimalna glavna snaga rezanja 130 kN - Konjički centar automatski se uvodi - Maksimalna masa obratka 70 t - Maksimalna masa obratka sa lunetom 100 t - Pogonska snaga 100 kW - Broj kliznih vodilica ležišta 4 - Dimenzije 22.000 x 6.200 x 2.900 mm - CNC upravljanje SIEMENS 840D (2010. za 220.000,00 €) - Posmična brzina suport X-Z 0,3 - 4.000 mm/min - Brzina brzog hoda suport X-Z 4.000 mm/min - Dimenzije unutrašnjeg konusa 140 x 1:7 - Mašina je u skladu sa CE direktivama - uključuje 2 lunete, 1 valjkasti oslonac, 4 stezne čeljusti, napravu za bušenje - Stanje: vrlo dobro stanje

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2000, obratovalne ure: 25.000 h, potovalna razdalja osi X: 10.300 mm, pomik osi Y: 2.000 mm, pomik po osi Z: 1.800 mm, hitrost pomika os X: 10 m/min, hitrost podajanja osi Y: 10 m/min, hitrost podajanja os Z: 10 m/min, položaj glave za glodanje: 2.5 x 2.5 °, največja hitrost vretena: 3.000 obr/min, hitrost vretena (min.): 60 obr/min, širina mize: 3.300 mm, dolžina mize: 12.000 mm, montažni premer: 50 mm, skupna višina: 48.750 mm, skupna širina: 100.000 mm, skupna dolžina: 212.000 mm, skupna masa: 100.000 kg, Duplex-Fräsmaschinen bestehen aus zwei Maschinen, die einander gegenüber angeordnet sind und entweder separat oder als eine Einheit betrieben werden können. Das Werkstück kann dabei mit zwei simultan arbeitenden Spindeln bearbeitet werden. Produktivitätssteigerung von bis zu 50 % im Vergleich zu konventionellen Lösungen, also Einzel-Fräsmaschinen Verbesserte Bauteilgenauigkeit, da die Bearbeitung in den meisten Fällen in nur einer Aufspannung erfolgt Ein einziger Bediener kann die DUPLEX-Fräsmaschinen steuern Geringerer Platz- und Investitionsbedarf im Vergleich zu zwei Einzelmaschinen Schnelle Amortisation der Investition aufgrund der hohen Produktivität DUPLEX-Lösungen ermöglichen verschiedene Konfigurationen: Einzelner Arbeitsraum oder Pendelbearbeitung Geeignet zur Bearbeitung von Baggerarmen/-auslegern wie z.B. von CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo X-Achse: 10.300 mm Gbodpfjrx Rxtex Anfjl Y-Achse: 2.000 mm Z-Achse: 1.800 mm Tischlänge: 12.000 mm Tischbreite: 3.300 mm Tischbelastung: 100.000 kg Spindelleistung: 22/30 kW Spindeldrehzahlen: 60 - 3.000 min⁻¹ Spindelaufnahme: 50 ISO / BT / MK Vorschub X-Achse: 10.000 mm/min Vorschub Y-Achse: 10.000 mm/min Vorschub Z-Achse: 10.000 mm/min Fräskopf, automatisch indexierend: 2,5 x 2,5° Betriebsstunden: 25.000 h Länge: 21.200 mm Breite: 10.000 mm Höhe: 4.875 mm Gewicht: 100.000 kg

Stanje: rabljeno, Leto izdelave: 2001, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 11087, vrsta vhodnega toka: Klimatska naprava, 2-disc fine grinding machine with accessories. Good condition. Includes lifting system. Complete documentation. Gsdpjq Nitvjfx Anfjbl

Stanje: generalkompletno obnovljen (rabljeno), Leto izdelave: 2006, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 119/020.0895, Izvor proizvodnje CH Napetost 400V Dimenzije 2700x2350x2100 mm Neto teža 4500 kg TEHNIČNI PODATKI Krmiljenje Fanuc 16i-T Višina konice 175 mm Razdalja med konicami 1000 mm Gbsdpelbgfcsfx Anfjl LINEARNE OSI Dolžina brušenja 500 mm Pomiki X: 267 mm Z: 650 mm BRUSILNI VRETENJAK Brezstopenjsko vrtljiv +/- 8,5° Dimenzije brusnega kamna 500x80x203 mm Moč 7,5 kW Hitrost 44 m/sek. VRETENJAK ZA OBDELOVANEC Vrsta konusa MK5 C-os +/- 5° Moč 1 kW Hitrost vrtenja 30-1000 min-1 PROTIDEL Vrsta konusa MK3 Hod pinole 35 mm Premer pinole Ø 50 mm Maks. masa obdelovanca 130 kg NAPAJANJE Napetost 400V 50 Hz Tehnični podatki so informativni in podvrženi spremembam ali napakam.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2005, Funkcionalnost: popolnoma funkcionalen,