BIESSE VRTALNA GLAVA 20 VRETENA

BIESSE

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2009, Funkcionalnost: nepreverjeno, število osi: 4, dolžina mize: 4.300 mm, širina mize: 2.200 mm, število vreten: 40, premer orodja: 120 mm, TECHNICAL DETAILS Number of spindles for vertical drilling: 30 Number of spindles for horizontal drilling in X-direction: 6 Number of spindles for horizontal drilling in Y-direction: 4 Total number of vertical + horizontal spindles: 40 Number of controlled axes: 4 Maximum tool diameter: 120 mm Table dimensions: 4,300 x 2,200 mm Number of positions tool magazine 1: 22 Number of positions tool magazine 2: 8 MACHINE DETAILS Milling motor power: 12 kW Total installed power: 42 kW Control software: BIESSEWORKS EQUIPMENT Automatic panel loading system Automatic panel stacking system Lift table Transport system Vacuum pump Gijdpfx Agsyq Ez Tewep Note: The safety fences at the rear and at the loading table are missing and will only be delivered if available. The machine is sold and delivered in its actual and legal condition ("as seen and agreed") based on photo documentation and technical/commercial documentation of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 7087

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2008, Funkcionalnost: nepreverjeno, višina obdelovanca (maks.): 90 mm, širina obdelovanca (maks.): 3.200 mm, dolžina obdelovanca (maks.): 3.200 mm, največja debelina roba: 3 mm, The machine has the following configuration: Number of panel sizing/milling units left side: 5 Milling unit (AS10) Double fine millers, top and bottom 2 pre-milling units Milling unit Number of edge processing units: 10 End trimming Top and bottom trimming (coarse) Fine trimming for bevel and rounding Corner rounding (AR34, 4 motors) Edge milling (FB40, 1 motor) Edge scraping Belt sanding (1 motor) Glue scraping Polishing (2 motors) Spray device TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 90 mm Panel length max.: 3,200 mm Panel width max.: 3,200 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm EQUIPMENT Conveyor chain with pushers Pressure with rubber belt Panel guiding rails, positioned by NC Edge roll magazine with 6 positions Hot-melt unit for PUR adhesive NORDSON Gisdpfxoyq Avhs Agwsp Roller set for edge pressing 4 pressure rollers with NC positioning Spray device mounted on overhead cabinets The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial documents of descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for the installation, securing, and utilization of the machine at the destination. External reference: 7685

Stanje: nepreverjeno (rabljeno), Leto izdelave: 2011, Funkcionalnost: nepreverjeno, potovalna razdalja osi X: 6.200 mm, pomik osi Y: 1.935 mm, višina obdelovanca (maks.): 250 mm, število osi: 4, število vreten: 40, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of vertical drilling spindles: 28 Number of horizontal drilling spindles in X direction: 4 Number of horizontal drilling spindles in Y direction: 8 Total number of drilling spindles: 40 Total number of tool changer positions: 22 Number of suction traverse beams: 10 Milling Unit Number of axes: 4 Motor power: 10.5 kW Automatic tool changer Giodpfxeyqzrnj Agwjp Edge banding unit Gluing unit Tool magazine Grooving unit Number of positions in tool magazine: 22 MACHINE DETAILS Main spindle power: 10.5 kW Total power: 31 kW EQUIPMENT Vacuum pump Safety net Chip conveyor The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 8011

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2021, potovalna razdalja osi X: 4.140 mm, pomik osi Y: 1.270 mm, pomik po osi Z: 275 mm, število osi: 5, This 5-axis BIESSE Rover A 1242 was manufactured in 2021. It features a working area of 4140 mm on the X-axis, 1270 mm on the Y-axis, and 275 mm on the Z-axis. The machine is equipped with brushless motors and a PC-based controller for enhanced performance. If you are looking for high-quality CNC woodworking machinery, you should consider the BIESSE Rover A 1242 that we offer for sale. Contact us for further details. • Working Area • Y (5-axis): 1270 mm • Y (4-axis): 1260 mm • Z (with vacuum modules H=74 mm): 230 mm • Z (with H=29 mm vacuum modules): 275 mm • Axes and Drives • X & Y: Rack and pinion drive; accuracy grade 6 • Z: Ball screw with preloaded nut; accuracy grade ISO C7 • Motors: Brushless motors with digital drives via Mechatrolink system • Control System and PC Hardware • Controller: BH660 (PC-based) with WRT (Windows Real Time) technology • CPU: Intel Core i5 or higher • RAM: 16 GB • Storage: 256 GB SSD or higher • Display: 21.5-inch LCD color monitor • Operating system: Windows with real-time process management extension • Connectivity: Ethernet card; USB ports • Electrical and Pneumatic • Power supply: 380 / 400 / 415 V - 50/60 Hz • Control voltage: 24 V DC (stabilized power supply) • Enclosure cooling: Air conditioning system for operation up to 40°C (104°F) • UPS (uninterruptible power supply): 7-10 minutes runtime for data backup • Workpiece Support (ATS system) • Workpiece supports: 8 ATS aluminum beams on linear guides • Module supports: 24 supports (132 × 132 × H41.5 mm) with pneumatic clamping • Set-up assistant (SA): Manual positioning with LED indicators; ±1.5 mm accuracy • Vacuum zones: 2 independent work areas in X; 2 independent clamping areas in X • Software and Licensing • Primary software: NC-HOPS 7 MacroCAM • Safety and Maintenance Gijdpfxeyt Rrve Agwep • Safety system: Bumper system (front and rear) for instant stop in the event of collision • Protection: Transparent polycarbonate front shield and sound-dampening cover • Lubrication: Automatic lubrication system for linear guides and rack/pinion Additional equipment • Vacuum pumps (standard/optional): Up to two units, each 90/100 m³/h or 250 m³/h

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2020, skupna masa: 3.800 kg, Ta 3-osna BIESSE Selco WN 2 je bila izdelana leta 2020. Ima robustno maso stroja 3900 kg in deluje na napetosti 400 VAC s porabo 12 kW. Stroj je zasnovan za učinkovito razrezovanje plošč in ima oznako CE za skladnost. Če iščete visokokakovostno formatno žago, priporočamo, da razmislite o stroju BIESSE Selco WN 2, ki ga prodajamo. Za več informacij nas kontaktirajte. • Teža krmilne omare: 190 kg • Napetost napajanja: 400 VAC • Polni tok: 24 A • Število faz napajanja: 3 Gijdpfx Aoyt Rkljgwjp • Poraba energije: 12 kW • Frekvenca: 50 Hz • Kratkostna vzdržljivost: 10 kA RMS • Dovod stisnjenega zraka: 6,5-7 bar • Zahtevana hitrost odsesavanja: 30 m/s • Oznaka CE: Da

Stanje: rabljeno, Funkcionalnost: nepreverjeno, Koda Ferwood: AGG0062 - Koda proizvajalca: 6314A0111 - Stanje: Rabljeno - Funkcionalnost: Ni testirano - Združljiv stroj: CNC BIESSE ROVER 23/24/27/30/346 - Če ste zainteresirani, nudimo storitev obnove, kontaktirajte nas. Teža in dimenzije za prevoz: 2,5 kg 20x20x20 cm Giodsvu Auuepfx Agwop

Stanje: nepreverjeno (rabljeno), Funkcionalnost: nepreverjeno, potovalna razdalja osi X: 3.200 mm, pomik osi Y: 1.300 mm, število vreten: 21, hitro pomikanje X-os: 80 m/min, hitri pomik os Y: 60 m/min, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS X-axis travel: 3,200 mm Y-axis travel: 1,300 mm X-axis traverse speed: 80 m/min Y-axis traverse speed: 60 m/min Z-axis traverse speed: 25 m/min Number of suction traverse beams: 6 Spindles Number of spindles for vertical drilling: 15 Number of spindles for horizontal drilling in X direction: 4 Number of spindles for horizontal drilling in Y direction: 2 Total number of spindles: 21 Milling Unit Number of axes: 3 Max. speed: 24,000 rpm Motor power: 9 kW Tool changer Number of positions: 10 MACHINE DETAILS Total power: 26 kW EQUIPMENT Vacuum pump WINDOWS-based control system WRT machine programming software The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial data sheets for descriptive purposes only. The buyer is entitled to inspect the goods before collection and assumes responsibility for installation, securing, and operation of the machine at the destination. Gsdeytr Ryepfx Agweip External reference: 8174

Stanje: rabljeno, Leto izdelave: 2014, skupna višina: 2.800 mm, skupna dolžina: 6.900 mm, skupna širina: 2.800 mm, Unladen weight: 6,100 kg Price: On request - Special features: Giodpfx Agjyr Rnuowep - Note: Repair of the B-axis and sealing leaks required - Year of manufacture: 2014 - Documentation available: No - CE certificate available: No - Serial number: 10333 - Number of milling spindles [pcs]: 2 - Milling spindle 1: - Number of controlled axes [pcs]: 5 - Milling spindle 2: - Number of controlled axes [pcs]: 3 - Type of milling table: Beam table - Tool clamping system: HSK-F63 - Workpiece clamping system: Pneumatic - Drilling unit available: Yes - Tool changer positions [pcs]: 45 - Safety features: Safety mat, safety fence, door interlock switch - Vacuum pump available: Yes - Quantity [pcs]: 2 - Manufacturer: Becker - Type: Vtlf 2.250 - Year of manufacture: 2011 - Main motor power [kW]: 5.5 - Capacity [m³/h]: 244 - Connection diameter [mm]: 60 - Vacuum [mbar]: 200 - Oil-free: Yes - Tools included: Yes - CNC documentation included: User keys/licenses, USB stick - Table length [mm]: 4,800 - Table width [mm]: 1,500 - Voltage [V]: 400 - Current consumption [A]: 39 - Fuse [A]: 63 - Power [kW]: 22.8 - Transport dimensions: 6,900 mm x 2,800 mm x 2,800 mm (L x W x H) - Transport weight [kg]: 6,100 kg - Number of transport packages [pcs]: 1 Financial information: VAT: The stated price is net, excluding VAT VAT/differential taxation: VAT is deductible for businesses Delivery and trade-in possible at any time for all industrial equipment Glenn Smeets

Stanje: dober (rabljeno), Leto izdelave: 2007, Funkcionalnost: popolnoma funkcionalen, vhodna napetost: 380 V, vhodni tok: 36 A, vhodna frekvenca: 50 Hz, vrsta vhodnega toka: trifazni, vrsta aktuacije: električni, skupna masa: 3.200 kg, priključek za stisnjen zrak: 7 letvica, Oprema: CE označba, Naprodaj pravi delovni konj. Stroj se ne boji dela ali trde roke. Gre za starošolski stroj, ki je res zanesljiv. Giedpfx Ageyudkuowep

Leto izdelave: 2020, stanje: pripravljen za uporabo (rabljen), Glavni pogon Moč motorja vretena: 13,2 kW Hitrost vretena: 24.000 vrt/min Število osi: 3 Gedpfxsx Nr Nps Agwjip Premiki Pomik po osi X: 3765 mm Pomik po osi Z: 378 mm Pomik po osi Y: 1560 mm Ta 5-osni BIESSE Rover PLAST A FT 1536 je bil izdelan leta 2020 in ima robustno elektro-varjeno osnovo ter visokonatančne pogonske sisteme. Ponaša se z glavnim elektrospindlom z močjo 13,2 kW, programirljivo hitrostjo vrtenja do 24.000 vrt/min in revolverskim menjalcem orodij z osmimi pozicijami. Idealno za zahtevno obdelavo lesa, vključuje 21,5'' LCD monitor in integracijo z Industry 4.0. Izkoristite priložnost za nakup CNC stroja za obdelavo lesa BIESSE Rover PLAST A FT 1536. Za več informacij nas kontaktirajte. Vrste uporabe CNC obdelava lesa