Portalni obdelovalni center

WALDRICH COBURG VALUTEC

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2003, Funkcionalnost: popolnoma funkcionalen, potovalna razdalja osi X: 4.000 mm, pomik osi Y: 3.000 mm, pomik po osi Z: 1.500 mm, obremenitev mize: 12.000 kg, največja hitrost vrtenja: 6.000 obr/min, število mest v zalogovniku orodij: 100, TECHNICAL DETAILS X-axis: 4,000 mm Y-axis: 3,000 mm Z-axis: 1,500 mm C-axis: -10 to 370° B-axis: -5 to 95° Table, longitudinal travel: 0 - 30 m/min Milling and drilling unit, horizontal: 0 - 60 m/min Spindle slide, vertical: 0 - 60 m/min Spindle unit horizontal/vertical: 0-15 / 0-10 rpm Passage height: 1,550 mm Passage width: 2,500 mm Table Clear height between table and spindle nose: 1,550 mm Clear width: 2,500 mm Table width: 2,000 mm Table length: 3,000 mm T-slots (crosswise): 22 H8 mm, spacing 250 mm T-slots (lengthwise): 15 H7 mm (250 mm from the outside, 10 mm deep) Max. table load: 12,000 kg Drill spindle speed range Fedew T Rx Ajpfx Ah Djpn 1st range: 5 - 1,400 rpm 2nd range: 25 - 6,000 rpm Max. torque: 800 Nm Drive power: 30 kW Spindle slide cross-section: 400 x 400 mm Tool system Tool holder according to DIN 69893: HSK-A 100 Number of tool positions: 100 Max. tool weight: 30 kg Max. tool diameter: 250 mm Max. tool length: 500 mm Station pitch: 140 mm Average chip-to-chip time: < 20 s Feed rates X-axis table longitudinal: 0 - 30 m/min Y-axis milling and drilling unit horizontal: 0 - 60 m/min Z-axis spindle slide vertical: 0 - 20 m/min C-axis spindle unit horizontal: 0 - 15 rpm B-axis spindle unit vertical: 0 - 10 rpm MACHINE DETAILS Total machine length: 9,500 mm Total machine width: 6,700 mm Total machine height above floor: 6,200 mm Coolant system Pump pressure: 12 bar (AKM), 50 bar (IKM) Delivery rate AKM: 40 l/min at 1 bar Delivery rate IKM: 20 l/min at 40 bar at the spindle Coolant principle: two-phase drum separator Coolant volume: 1,500 L Chip conveyor system Usable width, longitudinal conveyor: 450 mm (2 units) Usable width, cross conveyor: 225 mm (1 unit) Mounted on both sides of the machine bed, cross conveyor with overflow transfer

Stanje: dober (rabljeno), Leto izdelave: 2005, x-travel: 6000 mm y-travel: 3500 mm z-travel: 1500 mm Control: SIEMENS 840D Table load capacity: 12 t Height above floor level: 6300 mm Table size (longitudinal): 5000 mm Table size (cross): 2500 mm Number of tables: 2 Tool changer: 200 positions Maximum tool weight: 30 kg Tool holder: HSK A 100 Maximum tool diameter: 250 mm Maximum tool length: 500 mm Spindle speeds: 5–6000 rpm c-axis: -10 to 370° b-axis: 5 to -95° Column passage: 3000 mm Distance spindle nose to table: 1500 mm Machine weight: approx. 161 t Space requirement: approx. 20.5 x 11 x 6.3 m Fjdpfx Ajvwglvsh Dspn This WALDRICH-COBURG Valutec gantry milling machine is in very, very good condition and can be inspected at the seller’s facility by appointment.