Vpenjalna plošča s T-rezom

unbekannt 2545/1515/H835 mm

Stanje: dober (rabljeno), Clamping plate, scribing/marking plate, inspection plate, measuring table, welding table, aligning plate - Clamping plate is from a coordinate measuring machine - Width: 1335 mm - Length: 3000 mm - Height: 250 mm - Plate thickness: 40 mm - Plate features: with support ribs Gedpfx Aajfc T Tqe Uoiu - With 4x leveling feet - Quantity: 1 piece available - Transport dimensions: 3000 x 1335 x H750 mm - Weight: 2,749 kg

Stanje: rabljeno, Clamping Plate – Table of a Long Planer Machine – Table Width / Clamping Width: 1845 mm Table Length / Clamping Length: 5505 mm 7 longitudinal T-slots for T-slot nuts: M30 T-slot spacing: 263 mm Total length: 6230 mm Total plate height: 350 mm Giedpfxjbn Amfs Aa Ueu Weight: 11 t

Stanje: rabljeno, Mitre Cold Circular Saw Automatic KALTENBACH Type KKS 400 NA Machine No. 101701 Year of manufacture 1983 Saw blade diameter: 400 mm Cutting range at 90° round: Ø 130 mm Cutting range at 90° square: 120 x 120 mm Giodped N H A Nefx Aa Uou Cutting range at 90° rectangle: 305 x 20 mm Cutting range at 45° round: Ø 130 mm Cutting range at 45° square: 110 x 110 mm Cutting range at 45° rectangle: 245 x 30 mm Clamping range, vice feed: 30 to 140 mm Working height: 1000 mm Mitre cut: 0 - 180° Feed stroke: 600 mm Saw blade speed: 10 + 20 m/min, 2 stages Motor power: 1.7 and 2.6 kW Hydraulic motor: 1.5 kW Electrical connection: 380 Volt, 50 Hz - Hydraulic material vice feed with infeed roller conveyor left side, 1500 mm - Feed stroke via double feed up to 1200 mm (feed twice, then cut) - Hydraulic material clamping with vertical clamping cylinder - Mitre cut saw angle adjustable manually - Hydraulic feed control, cutting speed manually adjustable - 2 motor speeds for saw blade speed - Saw blade lift infinitely adjustable - Coolant device with electric pump in machine base - Hydraulic unit fixed to main machine body - Piece counter with zero shut-off Machine dimensions (L x W x H): 2600 x 1200 x 1900 mm Weight: approx. 1400 kg Good condition

Stanje: rabljeno, Length: 1800 mm Width: 1200 mm Machine weight approx.: 1.6 t Space requirement approx.: 1.8 x 1.2 x 0.4 m Gjdpfx Aascxxu Dj Uoiu - Measuring plate with 5 special feet - Good condition

Stanje: rabljeno, Leto izdelave: 2010, Maximum turning diameter: 320 mm Turning length: 810 mm Control: MSX 701 Maximum spindle speed: 6,000 rpm Drive power – main spindle: 22 / 18 kW Maximum usable bar diameter: 52 mm Gedpfxjv E R E Ao Aa Ueiu C-axis: 0.001° Spindle nose: JIS A2-5 Collet chuck: 140 mm Maximum spindle speed: 6,000 rpm Drive power – sub spindle: 22 / 18 kW Maximum usable bar diameter: 52 mm C-axis: 0.001° Spindle nose: JIS A2-5 Collet chuck: 140 mm Number of tool stations: 16 positions Number of driven tool stations: 16 positions Speed range – driven tools: max. 6,000 rpm Drive power – driven tools: 7.5 / 5.5 kW Y-axis travel: 110 mm Number of tool stations: 16 positions Number of driven tool stations: 16 positions Speed range – driven tools: max. 6,000 rpm Drive power – driven tools: 7.5 / 5.5 kW X-travel 1/2: 210 mm Y-travel: 110 mm Z-travel 1/2: 810 mm B-axis: 900 mm Total power requirement: 86 kVA Machine weight approx.: 8.1 t Space requirement approx.: 8.0 x 3.5 x 2.8 m CNC Turning and Milling Center MORI SEIKI - NZ 1500 T2Y - Main and sub spindle - 2 turrets, upper and lower - Y-axis - 2x 16 driven tool positions

Stanje: delavnici obnovljeno (rabljeno), Leto izdelave: 2007, obratovalne ure: 22.605 h, Funkcionalnost: popolnoma funkcionalen, stiskalna sila: 100 t, širina odprtine za polnjenje: 1.100 mm, dolžina polnilne odprtine: 1.600 mm, širina bale: 1.100 mm, višina bale: 1.100 mm, teža bale: 1.400 kg, skupna masa: 36.000 kg, kapaciteta rezervoarja za olje: 1.300 l, leto zadnje generalne obnove: 2025, For sale: Fully reconditioned baler with 100 t pressing force, large bale size 1100 x 1100 mm, 75 kW drive power, and 10-fold cross-tying. Technical data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main ram pressing force: 100 t Pre-pressing force: 50 t Operating hours: 22,605 hours Feed opening dimensions: 1,600 x 1,100 mm Filling volume / press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale size: 1,100 x 1,100 mm Drive power: 75 kW Total connected load: 126 kW Total current draw: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a bulk density of 30 kg/m³: approx. 16 t/hour bulk density of 50 kg/m³: approx. 25 t/hour bulk density of 100 kg/m³: approx. 47 t/hour Bale weights up to 1,400 kg, depending on material and bale length Hydraulic tank capacity: approx. 1,300 l PLC control: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Installed baler dimensions with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Notes: The baler was partially reconditioned, serviced, tested after completion, and stored in our workshop. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment work was performed: - Removal of rust and partial repainting of the press - Complete drainage of hydraulic oil tank, oil and air filters replaced - New hydraulic oil filled - All hydraulic hoses replaced - Main hydraulic cylinder, two pre-press flap cylinders, and compression channel cylinder removed, disassembled, inspected, cylinder tubes honed, all seal kits replaced, and final pressure test conducted Gedpfx Aajvf E Avs Ujiu - Pre-press flap disassembled with bearings and bearing blocks; first and third arc segments removed and rewelded - Both shaft bearings on the pre-press flap replaced - Upper material guide on pre-press flap frame replaced - Press ram dismantled, inspected, and both front guide rollers replaced - Material guides and wear plates on sides and base of press ram removed and rewelded - Horizontal and vertical needle and tying units dismantled, disassembled, inspected; plastic slide plates, twister shaft bearings, and wire deflector pulleys with bearings in the needle heads replaced - Both bronze slide rails left and right in the frame cover for the press ram replaced - Both wire deflection units left and right, with bale retention clamps completely replaced - Wire feed unit including hydraulic cylinder under needle passages completely renewed - Wire feed tracks in the floor and sidewalls of the press channel welded up and smoothed - General maintenance and servicing carried out according to manufacturer’s specifications - Baler tested in manual and automatic mode after refurbishment, accepted, and stored We accept no liability for the technical data or any potential errors.

Leto izdelave: 1996, stanje: dober (rabljeno), številka stroja/vozila: xxxx, High-Performance Bench Thread Tapping Machines on T-Slot Table Technical Data: - Thread tapping capacity approx. M3 – M16 Giedpfsf Tcy Dox Aa Usu - Speed range up to 500 rpm - Working area (pivot radius) 2500 mm - Quick-change tool holder, size 2, diameter 31 mm - Various inserts for quick-change tool holder - Table surface with 5 T-slots 2050 x 900 mm - Table height 910 mm - Machine vice with jaw width 200 mm - 3-jaw chuck 250 mm - Pneumatic connection with pressure regulator - Mobile base frame - Required space approx. W 2400 x H 2000 x D 1000 mm - Weight approx. 1100 kg

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, moč: 18,5 kW (25,15 KM), vrsta goriva: dizel, barva: modra, obratovalna teža: 3.375 kg, Leto izdelave: 2025, Novi mini bager RIPPA R 32 Pro, japonski motor Kubota, 4 valji, 18,5 kW, emisijski standard Euro 5, Tier 4 Stage V, priprava za hidravlično prijemalo, klimatska naprava, kamera za vzvratno vožnjo, letnik 2025, hitra menjava orodij, 1000 mm nagibna žlica, garancija. Gijdpswlvzusfx Aa Ueu

Leto izdelave: 1993, stanje: dober (rabljeno), številka stroja/vozila: 03.2370, Manufacturer: Arthur Klink Model: RISZ 10 x 1000 x 400 Year of manufacture: 1993 Weight: 6,500 kg (total) Machine No.: 03.2370 General / Technical Data: Used vertical hydraulic internal broaching machine with automatic workpiece feed for 2 workpieces, in good condition Pulling force: 10,000 kg Broaching length: 1000 mm Broaching stations: 3 units Gjdpfx Ascc D Ddja Usiu Distance between broaching stations: 125 mm Draw head holder diameter: 3 x Ø 80 mm Clear width between cylinders: max. 435 mm Cutting speed: hydraulically infinitely variable from 1 m/min up to max. 10.9 m/min Return speed: hydraulically infinitely variable from 5 up to max. 27.5 m/min Machine dimensions (W x D x H): approx. 5500 x 2800 x 4900 mm Power supply / connected load: 380 Volt, 50 Hz / 38 kW Accessories / Special Equipment: The machine is equipped with a workpiece table and a traverse support for 3 broaching stations. Furthermore, the machine features an automatic workpiece feeding system for 2 workpieces. Clamping of the shank and end-piece holders is hydraulic. The machine includes a coolant system with an integrated magnetic chip conveyor, enabling operation without the need for a special foundation (pit). Remarks: The machine is designed for use in large-scale series production. It is in very good condition and still has its original paint. The machine can be inspected under power in our warehouse.

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2000, obratovalne ure: 25.000 h, potovalna razdalja osi X: 10.300 mm, pomik osi Y: 2.000 mm, pomik po osi Z: 1.800 mm, hitrost pomika os X: 10 m/min, hitrost podajanja osi Y: 10 m/min, hitrost podajanja os Z: 10 m/min, položaj glave za glodanje: 2.5 x 2.5 °, največja hitrost vretena: 3.000 obr/min, hitrost vretena (min.): 60 obr/min, širina mize: 3.300 mm, dolžina mize: 12.000 mm, montažni premer: 50 mm, skupna višina: 48.750 mm, skupna širina: 100.000 mm, skupna dolžina: 212.000 mm, skupna masa: 100.000 kg, Duplex-Fräsmaschinen bestehen aus zwei Maschinen, die einander gegenüber angeordnet sind und entweder separat oder als eine Einheit betrieben werden können. Das Werkstück kann dabei mit zwei simultan arbeitenden Spindeln bearbeitet werden. Produktivitätssteigerung von bis zu 50 % im Vergleich zu konventionellen Lösungen, also Einzel-Fräsmaschinen Verbesserte Bauteilgenauigkeit, da die Bearbeitung in den meisten Fällen in nur einer Aufspannung erfolgt Ein einziger Bediener kann die DUPLEX-Fräsmaschinen steuern Geringerer Platz- und Investitionsbedarf im Vergleich zu zwei Einzelmaschinen Schnelle Amortisation der Investition aufgrund der hohen Produktivität DUPLEX-Lösungen ermöglichen verschiedene Konfigurationen: Einzelner Arbeitsraum oder Pendelbearbeitung Geeignet zur Bearbeitung von Baggerarmen/-auslegern wie z.B. von CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo X-Achse: 10.300 mm Y-Achse: 2.000 mm Z-Achse: 1.800 mm Tischlänge: 12.000 mm Gsdorx Rxtopfx Aa Ueiu Tischbreite: 3.300 mm Tischbelastung: 100.000 kg Spindelleistung: 22/30 kW Spindeldrehzahlen: 60 - 3.000 min⁻¹ Spindelaufnahme: 50 ISO / BT / MK Vorschub X-Achse: 10.000 mm/min Vorschub Y-Achse: 10.000 mm/min Vorschub Z-Achse: 10.000 mm/min Fräskopf, automatisch indexierend: 2,5 x 2,5° Betriebsstunden: 25.000 h Länge: 21.200 mm Breite: 10.000 mm Höhe: 4.875 mm Gewicht: 100.000 kg