DC zobniški motor

SEW-EURODRIVE RF83/GSV132.2LL/V/B

Stanje: zelo dobro (rabljeno), Leto izdelave: 2020, 1. WEISHAUPT WM-G10/4-A (z plinsko vejo) - Moč: 100-1100 kW - Izvedba: ZM-LN - Leto izdelave: 2020 2. WEISHAUPT WM-G10/3-A (z plinsko vejo) - Moč: 100-1000 kW - Izvedba: ZM - Leto izdelave: 2015 (1 kos), 2013 (2 kosa na voljo) 3. WEISHAUPT WM-G10/3-A (z plinsko vejo) - Moč: 125-900 kW - Izvedba: ZM-LN - Leto izdelave: 2011 4. WEISHAUPT WM-G10/3-A (z plinsko vejo) Bwedpfxswgyrte Afnoi - Moč: 100-1000 kW - Izvedba: ZM - Leto izdelave: 2011 5. WEISHAUPT WM-G10/3-A (z plinsko vejo) - Moč: 100-1000 kW - Izvedba: ZM - Leto izdelave: 2009

Stanje: zelo dobro (rabljeno), Leto izdelave: 2000, skupna masa: 2.000 kg, skupna dolžina: 3.000 mm, Mostno dvigalo ABUS - VS 2t x 3000 MACH-ID 9306 Bwjdpjx Dkxiefx Afnji Proizvajalec: ABUS Tip: VS 2t x 3000 Prosimo, upoštevajte: Podatki na tej strani so bili zbrani po najboljšem vedenju in, kjer je mogoče, od proizvajalca. Informacije so podane v dobri veri, vendar natančnost ni zagotovljena. Skladno s tem ti podatki ne predstavljajo ponudbe ali pogodbenih pogojev. Priporočamo, da preverite vse pomembne podrobnosti.

Stanje: zelo dobro (rabljeno), Epson G10-854SR Robot Assembly Station Dispensing Station The assembly station is divided into the following sub-stations: 3.1 Dispensing Area, 3.2 Assembly Area Heatsink + Front Wall Bracket, and 3.3 Assembly Area Front. (KK = Heatsink, SW = Front Wall Bracket) St.3.1: Dispensing Area - A workpiece carrier (WT) with mounted chassis and PCB enters the dispensing area via the transfer belt. - It is stopped at the lift-positioning unit (HuPo), lifted off the belt and fixed in place. - Next, the x-y-z handling system moves the dispensing head to the specified location and starts the dispensing process. - After successful dispensing, the handling system moves into the park position and the WT is set back onto the belt. - The carrier is then conveyed to the Assembly Area Heatsink + Front Wall Bracket (provided there is no WT in the placement position). St.3.2: Assembly Area Heatsink + Front Wall Bracket - A WT moves from the dispensing area into the Assembly Area Heatsink + Front Wall Bracket via the transfer belt. - It is stopped at the lift-positioning unit (HuPo), lifted off the belt, and fixed in place; at the same time, the chassis side walls of the partially assembled unit are aligned. - Simultaneously, the heatsink tray and front wall tray are positioned. - A stack of 12 heatsink trays and a stack of 12 front wall bracket trays are manually placed onto the respective infeed belts outside the safety enclosure. - The two safety interlocks are opened and the loaded tray stacks move into the gripping position of each stacker. - The safety interlocks close again. - The corresponding grippers pick up the respective tray. Bwodpfsibx S Nox Afnei - The tray is separated and transported upwards with the stacker z-axis to above the actual pick-up height. - To center and stabilize the tray, a centering support is pushed and positioned underneath each tray by the x-handling system. - With the stacker z-axis, each tray is set onto its corresponding centering support. - The trays are now ready for component removal. - Using the multi-gripper on the SCARA robot, the heatsink (KK) is gripped from the tray and placed in an intermediate alignment position (to compensate for pickup inaccuracies and ensure a repeatable gripping position for assembly). - The heatsink is scanned, picked up again, and if the scanner result is OK, it is assembled onto the WT. - If not OK, the heatsink is placed in an NOK box. - The SCARA robot multi-gripper then picks up the front wall bracket (SW) from the tray and places it in the alignment position. - The front wall bracket is picked up again and assembled onto the WT. - Proceed to Assembly Area Front. Technical Data Model: SCARA (4-axis robot) Payload: nominal 5 kg, max. 10 kg Horizontal reach: 850 mm Vertical reach: Axis 3: 420 mm Orientation range: J4: +/- 360° Horizontal repeatability: +/- 0.025 mm Vertical repeatability: J3: +/- 0.01 mm Orientation repeatability: J4: +/- 0.005° Max. operating range: Axis 1: +/- 152°, Axis 2: +/- 152.5°, Axis 3: 420 mm, Axis 4: +/- 360° Max. operating speed: J1,J2: +/- 11,000 mm/s, J3: +/- 2,350 mm/s, J4: +/- 2,400°/s Allowable moment of inertia: nom. 0.02 kg*m², max. 0.25 kg*m² User cabling electrical: 1x D-Sub 9 pin, 1x D-Sub 15 pin Z-Axis: Ø outer: 25 mm Press-in force: 250 N Weight: 48 kg Controller: EPSON RC180 Mounting type: ceiling IP Protection class: IP20 Power and signal cables: 3m Financing through our bank is also possible. Complete offer at komplett-konzept.leasingo.de

Stanje: rabljeno, Leto izdelave: 2018, številka stroja/vozila: 70035883, Pogon: kolesa Lastna teža: 2.170 kg Dvižna zmogljivost: 454 kg Delovna višina: 1.000 cm Transportne dimenzije (D x Š x V): 2,31 x 1,17 x 2,15 m Za več informacij se obrnite na PFEIFER GROUP. Bwsdpfxjtr Hv He Afnji