Vrtljiva miza za varjenje, vrtljiva naprava

Protec W 2000

Stanje: novo, Leto izdelave: 2025, nosilnost: 2.000 kg, Protec KT 2000 HV, hydraulically height-adjustable Load capacity: 2000 kg Handheld remote control with digital display Double foot pedal control Fpjdpfx Aencfvhjflsb Height approx. min. 800 mm (tilted to center), max. height 1400 mm Min. horizontal height: 1000 mm Faceplate diameter: 1200 mm Minimum tilt angle: 135° Speed: 0.05 to 0.9 rpm Motor power: 3 kW

Stanje: novo, Bending capacity: 6.0 mm Working length: 3100 mm Material thickness: 8.0 mm Total power requirement: 11.0 kW Weight approx.: 6.7 t Dimensions (LxWxH): 4,88 x 1,16 x 1,18 m Image similar Bending performance: 8.0 mm » at 3x top roll diameter. Pre-bending: 6.0 mm » at 1.5x top roll diameter. Top roll diameter: 230 mm Lower roll diameter: 210 mm Side roll diameter: 190 mm Max. opening: 30 mm Working height: 825 mm • Fully hydraulic drive of the top and bottom rolls via planetary gearboxes • Digital display for side roll positions • Hydraulic drop-end bearing • Cone bending device • Hardened rolls • Hydraulic adjustment of the side rolls, synchronized via PLC • Hydraulic adjustment of the lower roll via torsion shaft • Pressure-adjustable lower roll • Electric and hydraulic overload protection • Movable control panel • Operating manual in GERMAN and ENGLISH • Machine and equipment in compliance with CE regulations Catalog, see the following link: Important points for cone rolling: • The max. sheet thickness is 50% of the nominal capacity • Cone length must be a max. of 30% or more than 60% of the roll length • Hardened rolls are recommended Fedpjd Ab H Hefx Aflspb

Leto izdelave: 2023, Stanje: kot nova (razstavni stroj), Technical data: - Load capacity: 15,000 kg - Dead weight: 960 kg - Workpiece diameter (insertable): approx. 50 – 3,200 mm - Roller diameter: 250 mm - Roller width: 240 mm - Rotation speed: approx. 100–2,000 mm/min - Two-pedal foot switch - Potentiometer for stepless speed control Fodpfsd Iuqaox Aflepb

Stanje: novo, GRATMAXX Deburring Brush Machine The machine is suitable for deburring cut edges on: Round tubes, square tubes, rectangular tubes, solid materials, profiles of all kinds. Materials: Hard or soft steel, non-ferrous metals, plastics. Working process: Once the workpiece support and side stops are set, the burr-laden workpiece is lightly pressed against the brush, which rotates on its own axis. The workpiece itself does not need to be rotated, as this motion is performed by the brush. The type of workpiece material, burr thickness, as well as the desired edge rounding determine the contact pressure and duration, typically around 1–5 seconds. Technical Data: Material: Steel, stainless steel and non-ferrous metals (motor speeds 700–1,900 rpm, stepless) Min. workpiece diameter: 5 mm Max. workpiece diameter: 100 mm (150 mm) Brush dimensions: 2 pieces Ø300 (250) x 50 or 3 pieces Ø 300 (250) x 35 Drive power: 3.0 kW Connected load: 3.5 kW Operating voltage: 3~, 400 Volt, 50 Hz Rated current: 8A Pre-fuse: max 16A Fpsdjd Hmnfspfx Afleb Control voltage: 24V/DC Width: approx. 500 mm + handwheel 74 mm, + extraction nozzle 130 mm Height: approx. 1,382 mm Working height: approx. 1,080 mm Depth: 1,209 mm Weight: approx. 310 kg Sound pressure level: at 700 rpm 64 dB(A), at 1,500 rpm 74 dB(A), when processing a workpiece at max. speed 82 dB(A) Scope of delivery: GRATMAXX rotary head deburring brush machine with power socket, without cable Workpiece support table with adjustable angle stop and workpiece stops Tool for brush replacement Brushes not included in delivery! Accessories: F50201 Circular brush braided wire 0.38 mm F50202 Circular brush steel wire 0.2 mm F50203 Circular brush steel wire 0.38 mm F50204 Circular brush stainless braided wire 0.38 mm F50205 Circular brush abrasive nylon U180 F50206 Circular brush abrasive nylon U120 F50207 Circular brush stainless steel wire 0.20 mm Further technical details can be found in the attached PDF document.

Leto izdelave: 2024, Stanje: novo, Bending capacity: 6 mm Pre-bending: 5 mm Bending capacity: 6 mm Pre-bending: 5 mm Bending length: 2,030 mm Roll diameter: 170 mm Motor power: 4 kW Length: 3,600 mm Width: 1,020 mm Height: 1,120 mm Weight: 2,400 kg The machine can be inspected and demonstrated at any time by appointment at our demonstration center in Staufenberg. Fpsdpeftdh Iofx Aflsb Additional machines are available for demonstration at our location in Staufenberg. Further information is available upon request.

Stanje: novo, Leto izdelave: 2024, nosilnost: 300 kg, Welding rotary table Protec KT 300 H, 170/400 special version Horizontal load capacity: 300 kg, tilted load capacity: 150 kg Power supply: 220 V, 50 Hz Table diameter: 450 mm Hollow shaft diameter: 170 mm Table height: 500 mm Welding current transmission: 400 A Quick-action chuck diameter 300 mm, surcharge €550 Quick-action chuck diameter 400 mm, surcharge €750 Crank gear motor with stepless adjustment 0–90° Fpsdpfx Aferypmgolob Infinitely variable speed: 0.01 to approx. 5 rpm Incl. foot remote control Digital display with welding time limitation (optional)

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2024, nosilnost: 1.200 kg, Oprema: nožno daljinsko upravljanje, Varilna vrtljiva miza z nosilnostjo 1200 kg, certifikat CE. Zelo robustna izvedba. Hitrost je zvezno nastavljiva od 0,05 do 0,7 obr/min, po želji možno večjo hitrost. Premer vrtljive mize 1200 mm. Naklon do 120°. Višina v vodoravnem položaju 950 mm, nagnjena do sredine 720 mm. Ročno in nožno daljinsko upravljanje. Dimenzije: dolžina 1,35 m x širina 1,2 m. Fodpfxod A Etus Aflopb

Stanje: novo, Leto izdelave: 2025, premer valja: 140 mm, dolžina valja: 1.570 mm, - Capacity 1570 x 4.5 mm - Electrically adjustable rear roll - Electrically adjustable bottom roll (material clamping) - Digital readout for rear roll movement Fjdpfx Ajgg Nv Iofljpb - Digital readout for bottom roll movement (material clamping) - Hardened rolls - Conical rolling - Brake motor - Emergency stop - Documentation - 400V

Stanje: novo, Leto izdelave: 2024, nosilnost: 5.000 kg, Complete set incl. hand and dual foot remote control Digital speed display Hydraulic height adjustment Dimensions: Tilted height min: 800 mm Tilted height max: 1900 mm Fpsdpfx Afjl Dq U Uolsb Horizontal height min: 1050 mm Horizontal height max: 2000 mm Clamping plate diameter: 1500 mm Length: 2900 mm, Width: 1400 mm Weight: 3200 kg Rotational speed from 0.01 to approx. 0.9 rpm CE certification

Leto izdelave: 2018, Stanje: skoraj kot novo (rabljeno), Dumeta hydraulic height-adjustable welding positioner 500 kg load capacity, height-adjustable welding positioner with through-hole 100 - 200 mm Fpsdjhua Dqjpfx Afljb Table diameter: 700 mm Horizontal height: min. 0.6 m, max. 1.2 m Tilted height: min. 0.40 m, max. 1.0 m Rotation speed: 0.11 - 1.25 rpm Weight: 750 kg Tilting angle up to 135° Hand and foot remote control with speed display Very robust construction