Stroj za brizganje

KraussMaffei KM 160 - 750 CX

Stanje: zelo dobro (rabljeno), Leto izdelave: 2006, Krauss Maffei KM 160–750 CX Injection Moulding Machine Year of manufacture: 2006 Fully hydraulic clamping system. MC5 control system with colour monitor, integrated control panel, and built-in USB ports. Plasticising Unit 1 complete HPS-UN plasticising unit for thermoplastics: Screw diameter: 50 mm Non-return valve, open nozzle Nozzle radius: 10 mm Nozzle orifice: 4 mm Technical Data Clamping Unit Clamping force: 1,600 kN Mould opening force: 86.4 kN Moving platen force: opening: 44.8 kN Dsdex Thzpepfx Aflswa closing: 37.8 kN Platen dimensions (H × V): 820 × 845 mm Tie bar spacing (H × V): 520 × 520 mm Mould opening stroke: 650 mm Minimum mould height: 300 mm Total daylight (max. platen opening): 950 mm Ejector stroke: 150 mm Ejector force: 22.6 / 9.9 kN Injection Unit Screw diameter: 50 mm Injection pressure: 1,892 bar Injection volume: 393 cm³ Shot weight (PS): 357 g Screw speed (standard / optional): 390 / 490 rpm Electrical and Hydraulic Equipment Pump drive power: 22 kW Installed heater power: 10.97 kW Number of heating zones (barrel): 5 Dry cycle time (Euromap): 1,600 1/h Oil tank capacity: 489 l Dimensions and Weight Net weight with control cabinet: 6.0 t Machine dimensions (L × W × H): 4.6 × 1.6 × 2.1 m

Stanje: zelo dobro (rabljeno), Leto izdelave: 1998, Engel ES 330/80 HLS Schließkraft 80 Tonnen Baujahr 1998 Dwsdpfjpdr Aiex Aflja Schneckendurchmesser 35 mm Hubvolumen 154 cm³ Vergrößerte Aufspannplatte: 660 x 560 mm Minimale Werkzeug-Einbauhöhe: 200 mm

Stanje: zelo dobro (rabljeno), Leto izdelave: 2007, Krauss Maffei Injection Moulding Machine KM 110–750 CX Year of manufacture – 2007 Fully hydraulic clamping system. MC5 control with a colour monitor, integrated operator panel, and 3 USB ports. Plasticising Unit Complete plasticising unit for thermoplastics Version with abrasion protection Screw diameter: 40 mm Non-return valve Open nozzle TECHNICAL DATA Clamping Unit Clamping force: 1100 kN Mould opening force: 70 kN Movable platen force: - Opening: 35.4 kN - Closing: 31.4 kN Platen dimensions (h × v): 745 × 770 mm Tie bar spacing (h × v): 470 × 470 mm Mould opening stroke: 600 mm Minimum mould height: 300 mm Platen opening stroke: 900 mm Ejector stroke: 150 mm Ejector force: 22.6 / 9.9 kN Dwsdsx Avhyspfx Aflea Injection Unit Screw diameter: 40 mm Injection pressure: 2500 bar Shot volume: 251 cm³ Shot weight (PS): 228.41 g Screw rotation speed (standard/option): 295 / 355 rpm Electrical & Hydraulic Equipment Pump motor rated power: 22 kW Installed heater power: 15.62 kW Number of cylinder heating zones: 5 Dry cycles per Euromap: 2000 cycles/h Oil tank capacity: 489 l Dimensions and Weight Net weight with control cabinet: 6.2 t Machine dimensions (L × W × H): 4.9 × 1.6 × 2.1 m

Stanje: dober (rabljeno), Leto izdelave: 2005, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 1.600 kN, premer vijaka: 45 mm, razmak između stupova: 520 mm, delovna prostornina: 318 cm³, injekcijska masa: 289 g, Leto izdelave: 2005 Delovne ure: 80.228 ur Sila zapiranja: 160 ton Razdalja med stebri: 520 x 520 mm Premer vijačnice: 45 mm Dedszkqf Aepfx Aflewa Volumen vbrizgavanja: 318 cm³ Masa vbrizga: 289 g za PS Oprema: robot Krauss Maffei, jedrna vleka, Euromap, 3 dodatne brizgalne enote.

Stanje: novo, Leto izdelave: 2023, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 61036936, vpenjalna sila: 800 kN, premer vijaka: 35 mm, delovna prostornina: 135 cm³, tlak vbrizgavanja: 1.837 letvica, injekcijska masa: 123 g, minimalna višina orodja: 150 mm, izmetalna sila: 22.000 N, hod izmetalca: 100 mm, odmični hod: 750 mm, vgradna višina: 400 mm, skupna dolžina: 4.750 mm, skupna širina: 1.670 mm, skupna višina: 1.820 mm, skupna masa: 5.900 kg, ogrevalna zmogljivost: 8,9 kW (12,10 KM), vrsta pogona: Vollelektrisch, prosta razpetina: 470 mm, teža orodja: 600.000 g, Injection moulding machines directly from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines: The base injection moulding machine, precisionMolding, is the perfect entry-level solution for all-electric injection moulding, enabling rapid and innovative responses to market requirements. It combines high performance, user-friendly operation, and short delivery times. The machine can be used across various application areas, such as the packaging industry, electrical and electronics industry, medical technology, and the automotive sector. Your benefits: – Optimised price-performance ratio for a wide range of applications – High energy efficiency thanks to the all-electric machine concept – Fast delivery times realised through basic machine concept with a broad spectrum of options TECHNICAL DATA: KM 80 / 250 PA G01 (Order 38670013) (Machine no.:61036936, new, Year 2023) CONTROL SYSTEM • MC P1 with 15" TFT colour display and multi-touch function CLAMPING UNIT • Clamping force kN 800 • Maximum mould opening force kN 120 • Daylight (h x v) mm 470 x 420 • Mounting platens (h x v) mm 610 x 560 • Minimum - maximum mould height mm 150 - 400 • Maximum opening stroke mm 750 • Maximum mould opening travel mm 350 • Ejector drive electric • Ejector stroke mm 100 • Ejector force forward/back kN 22 / 22 • Ejector speed forward/back mm/s 300 / 300 • Maximum mould weight kg 600 INJECTION UNIT • Screw diameter / type mm 35 / standard • Effective L/D ratio 20.0 • Injection pressure bar 1837 • Stroke volume cm³ 135 • Shot weight at max. stroke (PS) g 123 • Injection speed mm/s 200 Dodpfx Ajuggb Dsflowa • Injection flow rate cm³/s 192 • Screw drive / speed 1/min 382 • Plastification rate (standard screw) g/s 19.5 • Nozzle contact force kN 30 ELECTRICAL PARAMETERS • Connected load kW 17.8 • Installed heating capacity kW 8.9 • Power supply V / Hz 400 / 50, 3-phase with neutral WEIGHT AND DIMENSIONS • Net weight with control cabinet t 5.9 • Length x Width x Height m 4.75 x 1.67 x 1.82 ADDITIONAL EQUIPMENT • Wear-resistant plastification • BluePower full insulation of plastification cylinder • Open nozzle • Air valve, single (BWAP) • Pneumatic control for hot runner shut-off, single • Electrical interface (cascade), 4-fold • Electrical preparation for hydraulic auxiliary unit • Euromap interface for handling, E18, E63 • Euromap interface (central computer), E67, E77 • Water manifold, 4-fold • Automatic central lubrication • Adaptive Process Control (APC) • Injection-compression moulding function • Graphics analysis package • Swivelling device for injection unit The machine is located at our factory in Parsdorf and is available at short notice. Additional optional features can be offered on request. We look forward to your enquiry.

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2011, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 1.600 kN, premer vijaka: 50 mm, delovna prostornina: 393 cm³, Clamping Force: 1600 kN Max. Tool Opening Force: 87 kN Moving Platen Drive Force (opening): 45 kN Moving Platen Drive Force (closing): 38 kN Clamping Plate (H x V): 820 x 845 mm Clear Tie Bar Spacing (H x V): 520 x 520 mm Mould Opening Stroke: 650 mm Min. Mould Installation Height: 300 mm Max. Opening Width: 950 mm Ejector Stroke: 150 mm Ejector Force (forward/back): 23 kN Injection Unit: Screw Diameter: 50 mm L/D Ratio: 20 Injection Pressure: 1892 bar Stroke Volume: 393 ccm Dwedpoy Nlb Sjfx Aflea Shot Weight (PS): 358 g Injection Flow Rate: 177 ccm/s Screw Speed: 265 rpm Plasticizing Rate: 36.2 g/s Nozzle Contact Force: 50 kN Electro-Hydraulic Equipment: Rated Pump Motor Power: 22 kW Installed Heating Capacity: 16 kW Cylinder Heating Zones: 5 Oil Capacity: 489 l Dimensions & Weights: Floor Space Approx.: 5.50 x 2.00 x 2.20 m Overall Weight: 8200 kg Max. Mould Weight: 1862 kg Accessories: - Oscillation elements - BluePower - Servo Pump Drive Additional Equipment: - 1 x Air Valve - 8 x Hot Runner Control Zones - 2 x Core Pull on Moving Platen - 2 x Core Pull on Fixed Platen - Robot Interface according to Euromap 67

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2006, obratovalne ure: 68.590 h, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 1.600 kN, premer vijaka: 50 mm, delovna prostornina: 393 cm³, Clamping Force: 1600 kN Max. Tool Opening Force: 87 kN Movable Platen Opening Force: 45 kN Movable Platen Closing Force: 38 kN Clamping Plate (H x V): 820 x 845 mm Clear Distance (H x V): 520 x 520 mm Mould Opening Stroke: 650 mm Min. Mould Installation Height: 300 mm Maximum Opening Width: 950 mm Ejector Stroke: 150 mm Dwedsydp D Eepfx Aflsa Ejector Force Forward/Return: 23 kN Injection Unit: Screw Diameter: 50 mm L/D Ratio: 20 Injection Pressure: 1892 bar Shot Volume: 393 ccm Shot Weight (PS): 358 g Injection Flow Rate: 177 ccm/s Screw Speed: 265 rpm Plasticizing Rate: 36.2 g/s Nozzle Contact Force: 50 kN Electrohydraulic Equipment: Pump Motor Rated Power: 22 kW Installed Heating Capacity: 16 kW Cylinder Heating Control Zones: 5 Oil Capacity: 489 l Dimensions and Weights: Space Requirement approx.: 5.50 x 2.00 x 2.20 m Total Weight: 6600 kg Max. Mould Weight: 1862 kg Accessories: - Oscillation elements - Krauss Maffei Robot LR 100 X: 550 mm Y: 1200 mm Z: 2500 mm C: 0-90° Additional Equipment: - 1x air valve - 2x core pull - Robot interface according to Euromap 67

Stanje: zelo dobro (rabljeno), Leto izdelave: 2000, Refrigeration units Dwjdsd I Tlhopfx Aflea Brand: Ers Model: SC 110. V/5 Power: 8 kW Year of manufacture: 2000

Stanje: zelo dobro (rabljeno), Leto izdelave: 2009, številka stroja/vozila: 241.125, Funkcionalnost: popolnoma funkcionalen, Horizontalna žaga panelka proizvajalca Schelling, namenjena rezanju lesnih materialov. HPO – program za optimizacijo rezanja Izvlek žaginega lista: največ 95 mm Pomik vozička žage do 120 m/min Dolžine reza: Model FH 4 430 - 4.300 mm Možno ogledati v delujočem stanju do začetka leta 2026 (načrtovana demontaža) Dedpex Ebzdofx Afljwa Največji premer žaginega lista – 350 mm Izvlek – 95 mm Odpiranje vpenjalca 90 mm Moč motorja žage – 15 kW Premer predrezila 300 mm Podajalna hitrost naprej do 80 m/min nazaj 80 m/min Podajalna hitrost žage naprej do 120 m/min nazaj 120 m/min

Stanje: skoraj kot novo (rabljeno), Leto izdelave: 2008, obratovalne ure: 58.000 h, Funkcionalnost: popolnoma funkcionalen, vpenjalna sila: 1.000 kN, Superbly maintained injection moulding machine from a cleanroom (pharmaceutical production) - Fully operational with functionality guarantee - Equipped with GEKU SR 500 ST linear robot - Excellent cosmetic condition Technical Specifications Manufacturer: Engel Model: e-max 200/100 Serial Number: 170609 Year of Manufacture: 2008 Operating Hours: approx. 58,774 h Dimensions (L/W/H): 4.0 x 1.3 x 1.9 m Weight: 3,900 kg Functionality: fully operational Condition: excellent cleanroom Special Features Control system: CC200 Screw diameter: 25 mm Shot weight: 55 g/PS Injection pressure: 2,400 bar Injection volume: 59 cc Clamping force: 1,000 kN / 100 t Tie bar spacing: 460 x 410 mm Platen size: 650 x 600 mm Mould height: 150-450 mm Dedpfoubamvsx Afljwa Max. platen distance: 800 mm Opening stroke: 350 mm Ejector stroke / force: 100 mm / 25 kN Clamping unit: electric Connected load: 45 kW Rated current: 69 A The machine is available immediately at our warehouse in Hannover, Germany, and has been tested. Extras GEKU Robot Type: SR 500 ST Control: Simotion X-axis: 600 mm Y-axis: 1,400 mm (vertical) Z-axis: 2,500 mm (horizontal) A flip axis: SWM 45 C-axis: Servo Gripper: SWS16 B-axis: not present Warranty Warranty valid until first commissioning. Loading/Shipping FCA – Free loading onto buyer’s truck or delivered free to destination against freight reimbursement from our warehouse in Hannover, Germany Financing On request – hire purchase option Price: On request