Hidravlični stroji za valjanje pločevine s 4 valji

KK-Industries CY4R-HHS 230-20/13

Stanje: novo, Leto izdelave: 2025, TFON sistem zaobljevanja robov in obdelave površin Sistem zasnovan za izjemno prilagodljivost in natančnost omogoča obdelavo konstrukcijskega jekla, aluminija in nerjavnega jekla v debelinah od 0 do 120 mm. Napredna rešitev zaobljevanja robov in čiščenja površin je razvita za najzahtevnejše industrijske namene. Združljivost materialov: • Konstrukcijsko jeklo, aluminij, nerjavno jeklo Obseg debelin obdelave: • 0 – 120 mm Zaobljenje robov: • R2 zaobljenje robov zagotavlja gladke, varne robove, kar dviguje tako estetiko kot funkcionalnost. Natančen nadzor: • Vgrajen Siemens avtomatizacijski sistem omogoča zanesljiv in dosledno natančen nadzor skozi celoten proces. Neodvisne obdelovalne postaje: • Več postaj omogoča vzporedno ali zaporedno obdelavo za prilagodljive proizvodne procese. Izbira velikosti miz: • Na voljo s širino delovne mize 650 mm, 1000 mm ali 1300 mm za raznolike proizvodne potrebe. Vrste miz: • Magnetna, vakuumska ali kombinirana magnetno-vakuumska miza za varno in prilagodljivo vpenjanje različnih materialov in formatov obdelovancev. Plazemska & kisikova tehnologija: • Napredni plazemski in kisikovi sistemi učinkovito odstranijo grobe robove in žlindro po rezanju ter zagotavljajo čiste površine. Čiščenje površin: • Učinkovito odstrani umazanijo, rjo, okside in lusko ter pripravi obdelovance na nadaljnje postopke, kot sta varjenje ali površinska zaščita. Zaobljeni robovi za zaščitne premaze: • Doseženi so enakomerni, napak prosti robovi, optimalni za barvanje in druge premaze. Industrijska uporaba: • Jeklarska servisna središča, energetika, rudarstvo, gradbeništvo, avtomobilska industrija – zasnovano za težka in visoko zahtevna okolja. Enotni rezultati zaobljenja: • 8 lamelnih brusnih kolutov zagotavlja dosledno R2 zaobljene robove na vseh delih. Pnevmatski nihajni sistem: • Podaljšuje življenjsko dobo brusnega traku in ohranja stalno kakovost skozi pnevmatsko nihanje. Oblikovano za industrijsko natančnost. Zgrajeno za vzdržljivost. Prilagodljivo za široko področje uporabe. TFON – odličnost pri zaobljenju robov in pripravi površin. Dkodpfxei E Tkae Afleg

Stanje: novo, Pre-bending: 13.0 mm Working length: 3100 mm Plate thickness: 16.0 mm Total power requirement: 17.5 kW Approx. weight: 11,600 kg Dimensions (LxWxH): 5.31 x 1.66 x 1.59 m Image similar Bending capacity: 16.0 mm » at 3x top roll diameter Pre-bending: 13.0 mm » at 1.5x top roll diameter Top roll diameter: 300 mm Bottom roll diameter: 270 mm Side roll diameter: 210 mm Maximum opening: 50 mm Working height: 1140 mm Dodjd Auacopfx Aflskg • Fully hydraulic drive of top and bottom rolls via planetary gearbox • Digital display for side roll positions • Hydraulic drop-end bearing • Cone bending device • Hardened rolls • Hydraulic adjustment of side rolls synchronized via PLC • Hydraulic adjustment of bottom roll via torsion shaft • Pressure-adjustable bottom roll • Electrical and hydraulic overload protection • Movable control panel • Operating manual in GERMAN and ENGLISH • Machine and equipment in compliance with CE regulations Important notes on cone rolling: • The maximum sheet thickness is 50% of the rated capacity • The cone length may be max. 30% or must be more than 60% of the roll length • Hardened rolls are recommended

Stanje: novo, Bending capacity: 6.0 mm Working length: 3100 mm Material thickness: 8.0 mm Total power requirement: 11.0 kW Weight approx.: 6.7 t Dimensions (LxWxH): 4,88 x 1,16 x 1,18 m Image similar Bending performance: 8.0 mm » at 3x top roll diameter. Pre-bending: 6.0 mm » at 1.5x top roll diameter. Top roll diameter: 230 mm Lower roll diameter: 210 mm Side roll diameter: 190 mm Max. opening: 30 mm Djdjd Ab H Hjpfx Afljkg Working height: 825 mm • Fully hydraulic drive of the top and bottom rolls via planetary gearboxes • Digital display for side roll positions • Hydraulic drop-end bearing • Cone bending device • Hardened rolls • Hydraulic adjustment of the side rolls, synchronized via PLC • Hydraulic adjustment of the lower roll via torsion shaft • Pressure-adjustable lower roll • Electric and hydraulic overload protection • Movable control panel • Operating manual in GERMAN and ENGLISH • Machine and equipment in compliance with CE regulations Catalog, see the following link: Important points for cone rolling: • The max. sheet thickness is 50% of the nominal capacity • Cone length must be a max. of 30% or more than 60% of the roll length • Hardened rolls are recommended

Leto izdelave: 2002, Stanje: rabljeno, Diameter 180 mm Workpiece length 0 mm Workpiece width 1350 mm Total power requirement 65 kW Machine weight approx. 7,500 kg Required floor space approx. m T I M E S A V E R S (Netherlands) Wide Belt Deburring and Finishing Machine Model 41 Series 1350 WRDOW-N Year of manufacture 2002 Serial No. 2313-03 _____ Sanding width approx. 1,350 mm Max. workpiece height approx. 1 – 50 mm Feed speed variable approx. 1 – 10 m/min Comprising the following units: 1.) Vacuum table with flat workpiece feed belt, 780 mm vacuum track in the center of the belt. Belt feed motor approx. 3 kW, frequency controlled for continuously variable feed rate 1 – 10 m/min. Selector switch for forward and reverse belt run, digital display for belt speed and continuous table height adjustment. Suitable for wet processing. 2.) Contact roller approx. Ø 180 mm x 1350 mm wide, drive approx. 15/19 kW, belt speed approx. 11-22 m/s with fine height adjustment and pneumatic oscil- lation across the width, various sanding belts included. 3.) Vertical sanding/deburring disc (disc brush system) approx. Ø 1200 mm, consisting of self-adhesive nonwoven abrasive in various grades available, specially for deburring and cleaning surfaces as well as for radii rounding on workpieces. Also suitable for workpieces with varying heights. Drive approx. 7.5 kW, disc oscillates motor-driven (2.2 kW) across the entire belt width. 4.) Contact roller approx. Ø 180 mm x 1350 mm wide, drive approx. 18.5 kW, belt speed approx. 11 m/s with fine height adjustment and pneumatic oscil- lation across the width, various sanding belts included. 5.) Wet processing version = complete coolant system consisting of belt filter unit with pump installed in machine base, rotary union on top of the deburring disc spindle, return of coolant via the vacuum table, and water mist separator above the machine, with blower approx. 5.3 kW. Side doors in V2A stainless steel sheet, oil skimmer, etc. 6.) Side-mounted control panel with clear controls and digital position and speed display. Joystick for feed belt and table adjustment, 3 x ammeters, etc. as well as front and rear workpiece pressure rollers, emergency stop Total drive power approx. 65 kW - 400 V – 50Hz Weight approx. 7,500 kg Required room height approx. 3.50 m Dkodpfx Afst Hw Sholog Condition: good – available for demonstration under power Delivery: ex stock – as inspected Payment: strictly net – upon receipt of invoice

Stanje: novo, Pre-bending: 10.0 mm Sheet length: 2550 mm Sheet thickness: 13.0 mm Total power requirement: 15.0 kW Approx. weight: 10,600 kg Dimensions (LxWxH): 4.76 x 1.66 x 1.59 m Dsdpfjd Ab H Isx Aflskg Image similar Bending performance: 13.0 mm » with 3x top roll diameter Pre-bending: 10.0 mm » with 1.5x top roll diameter Top roll diameter: 270 mm Lower roll diameter: 250 mm Side roll diameter: 220 mm Max. opening: 50 mm Working height: 1,155 mm • Fully hydraulic drive of the top and bottom rolls via planetary gear • Digital readout for side roll positions • Hydraulic drop-end bearing • Infinitely variable rolling speed • Cone bending device • Hardened rolls • Hydraulic side roll adjustment synchronized via PLC • Hydraulic lower roll adjustment via torsion shaft • Pressure-adjustable lower roll • Electrical and hydraulic overload protection • Mobile control panel • Machine and equipment in accordance with CE directives See catalogue via the following link:       Important notes for conical rolling: • The max. sheet thickness is 50% of the nominal capacity • The cone length may be max. 30% or must exceed 60% of the roll length • Hardened rolls are recommended

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: 0684, največja dovoljena obremenitev: 40.000 kg, skupna masa: 44.500 kg, dolžina tovornega prostora: 4.000 mm, širina tovornega prostora: 2.200 mm, višina nakladalnega prostora: 780 mm, velikost pnevmatike: 405x260, stanje pnevmatik: 100 odstotek, Leto izdelave: 2025, Transportni voziček TPW 40 AL-PA-AW Tip: TPW 40 AL-PA-AW Serijska številka: 0684 Letnik: 2025 Nosilnost: 40.000 kg na 60% tovorne površine pri 6 km/h Dimenzije: Dolžina tovorne površine: 4000 mm Širina: 2200 mm Višina: ca. 760 mm Krmiljenje: Krmiljenje na vse štiri kolesa, nihajna os, nihajna gugalnica osi Oprema: 16 koles za težke obremenitve 405-260 Vlečna ojnica: Dolžina vlečne ojnice 1800 mm z varovalom proti padcu in vlečno uho po DIN za čep 40 mm Barva: RAL 2000 Transportno dno: 50 mm duglazija-macesen, v okvir privito z utopno vijačenjem Dedpfx Aefxgxnoflekg #prevoz težkih bremen #notranji transportni sistemi #težki priklopnik 6–100 ton #težki priklopniki od 3 do 100 ton #platformni voz za težke tovore #platformni priklopnik za težke tovore #krmiljenje na vse štiri kolesa #transportni voziček

Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2009, Options: ACB, BendGuard for manual bending, HQ version, interface to a second machine Dkedjwykccopfx Aflog

Stanje: novo, Ostas 4-Roll Plate Bending Machine 4R OHS 2070 x 220 - Hydraulic side roller adjustment - Hydraulic drop-end bearing - Hardened rolls - Conical bending device - Separate control panel - Roll length: 2000 mm - Top roll diameter: 220 mm - Side roll diameter: 180 mm - Total motor power: 4+3 kW Dkodpjtvn D Tsfx Afleg - Weight: 4,900 kg - Dimensions (mm): 4050 x 1550 x 1470 (L x W x H) Performance Data – Bending: - 11 mm at minimum inside diameter (5 x top roll) - 9 mm at minimum inside diameter (1.5 x top roll) Performance Data – Pre-bending: - 9 mm at minimum inside diameter (5 x top roll) - 7 mm at minimum inside diameter (1.5 x top roll) All bending capacities are calculated based on a yield strength of 250 N/mm² Material (ST 37 – ST 42 structural steel) Installed Optional Equipment: - Infinitely variable roll speed - NC control

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2024, laserska moč: 12.000 W, BAISON V52U (12+12 mètres) : (12 ou 20 kW) MACHINE DE COUPE LASER FIBRE POUR TUBES LOURDS À QUATRE MORS AVEC SYSTÈME DE CHARGEMENT ET DE DÉCHARGEMENT AUTOMATIQUE Système de chargement automatique 12 mètres + système de déchargement automatique 12 mètres (Possibilité d'équipements en différentes configurations, par ex : 12+6 mètres) Cette machine est également adaptée pour la découpe de profilés, tubes et différentes formes. Capacité tubes : Tube rond : φ50-φ500 mm Tube carré : □50*50 - □500*500 mm Poutrelle U : 5#-50# Cornière : 200*200 mm Poutrelle I : 10#-50# Poutrelle H : 100*100 mm - 500*500 mm Puissance laser : 12 000 W (Raycus) Poids max. du tube unitaire : 2 000 kg Course des mors : course intégrale Longueur minimale restante : 0 mm Vitesse max. des mandrins : 40 tr/min Vitesse max. : 50 m/min Accélération max. : 0,4 G Longueur max. de coupe tube : 12 000 mm Longueur résiduelle ultra-courte : 0 mm X-axis : 500 mm Y-axis : 12 000 mm Z-axis : 500 mm Précision de positionnement (X/Y) : ±0,05 mm/m Précision de répétabilité (X/Y) : ±0,05 mm Données de puissance : 130 kW / 225A Alimentation électrique : 380V/50Hz/3 phases Indice de protection machine : IP54 Dimensions machine : 29 080 x 5 000 x 3 250 mm Poids machine : 28 165 kg (incluant système de chargement semi-automatique et système de déchargement automatique) Configuration : ACCESSOIRES INCLUS Source laser RAYCUS 12 kW Tête laser à focalisation automatique – RAYTOOLS BS12K-3D Contrôleur – FSCUT 5000A Mandrins pneumatiques auto-centrants automatiques Système de chargement semi-automatique par chaîne Servomoteurs VEICHI Réducteur TECHMECH Transmission X/Y de haute précision par crémaillère et rails K.H Rails de guidage SHAC Système industriel de refroidissement/chauffage bi-zone du laser – HANLI Vanne proportionnelle AVENTICS Bâti mécano-soudé traité thermiquement – BAISON Télécommande sans fil Ordinateur sous interface Windows 11, Internet & WIFI Système centralisé de lubrification automatique Système d’extraction des fumées à turbine centrifuge Manuels d’utilisation, maintenance et programmation Stabilisateur et régulateur de tension Conforme aux normes CE Pourquoi choisir CNC Top Ten bv ? - CNC Top Ten bénéficie de plus de 50 ans d'expérience dans les machines CNC. - Nous possédons de nombreux centres de vente et de service en Europe de l’Ouest et de l’Est. - Notre équipe assure un service, une installation et une formation respectueux et maîtrisés dès le début. - Pour cette machine, installation et formation sur 2 semaines (non inclus dans le prix et calculé selon localisation client). - Machines pour coupe tubes et profilés. - La fibre laser, technologie "verte" d’avenir. - (Économies d'au moins 50% sur les coûts énergétiques) - Composants très fiables, entretien minimal - Jusqu’à 50% d’économie par pièce grâce à une production plus efficiente - Précision de coupe et finition de surface de haute qualité - Structure mécano-soudée très robuste - Composants de marques reconnues, durables et haut de gamme - En option : barrière immatérielle de sécurité - Entièrement conforme CE Vendeur officiel Djdpfovcbw Djx Aflskg CNC Top Ten bv Coevorden, Pays-Bas

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2025, vrsta laserja: vlakenski laser, laserska moč: 12.000 W, Oprema: CE označba, centralizirani mazalni sistem, dokumentacija / priročnik, hladilna enota, menjalnik šob, nujno zaustavitev, odsesavanje hlapov, odsesavanje prahu, varnostna svetlobna zapora, Поддерживает резку стальных труб длиной до 12 м Оснащён полностью автоматизированной системой комплексной подачи и выгрузки Интеллектуальное решение «одна станция» для загрузки, резки и выгрузки, повышение производительности до 200% Поддержка множества технологических операций: фасонная резка (скош), замковка, резка, пробивка отверстий, формирование сварочных отверстий, вырезание отверстий под болты, маркировка и нанесение меток Лазерная мощность 12 000–20 000 Вт Перемещение по оси X 1 600 мм Перемещение по оси Y 1 900 мм Перемещение по оси Z 900 мм Поворот по оси A ±90° Поворот по оси C ±90° Перемещение по оси U 30 мм Перемещение по оси V 13 000 мм Точность позиционирования ±0,1 мм Максимальный размер обрабатываемого профиля 1 000 × 400 мм Максимально поддерживаемый вес 5 т Dsdpfow A H T Ajx Afljkg Поддерживаемые профили двутавр, швеллер, балка I-типа