Vibracijski stroj za dodelavo

ERBA ESA 15 Prozesswasser-Zentrifuge

Stanje: nepreverjeno (rabljeno), Number of sanding units: 4 pcs Sanding width: 190 mm Max. sanding height: 4–180 mm Weight: 4200 kg Hess Expert 4-Belt Single-Piece Wood Sander Ø Sanding from below and above Ø Each with 2 staggered sanding units (top and bottom) Ø Sanding units (top and bottom) connected in series according to the precision planing principle Ø Pre-sanding with coarse grit (calibration) Ø Fine sanding with fine grit (finish) Ø Central motorized height adjustment of the lower sanding units Ø Central motorized and synchronous height adjustment of the complete upper sanding and brushing units, including the upper transport units Ø Oscillating belt use (during the sanding process) Ø Absolute power transmission via 5.5 kW motors and large dimensioned drive drums Ø Oxide-ceramic sanding shoe for - precise surface geometry - no readjustment required - permanent dimensional accuracy - completely maintenance- and wear-free Basic structure: Stable, heavy welded construction made of thick-walled rectangular profiles with additional, statically calculated stiffeners for optimal vibration damping. Staggered sanding units with large-diameter belt drive drums for slip-free belt tracking. Dual-point extraction for direct and airborne dust with sealing brushes and integrated sanding belt air-blast device to extend belt service life. Sanding units in robust steel plate construction serve as the base for vibration-damped, smooth belt operation. Absolutely backlash-free guidance by ball-type linear sets made of hardened and ground shafts. Height adjustment of the sanding units via hardened and ground special linear guides and preloaded carriage units. Long-term precision is ensured by dust and dirt protection of the ball linear sets and carriage units. Large-diameter presanding rollers as contact drums. Contact drums and sanding shoes are balanced relative to the sanding belt grit stress. The oversized drive drums guarantee the full power transmission of the 5.5 kW sanding motors to the sanding belt, ensuring slip-free, stable running and optimal heat dissipation, allowing for maximum material removal. Automatic machine stop in the event of belt breakage. Optical display at the control panel and via signal light on the machine. Tedpfx Anot Tqy Ejpod Sanding shoes for finishing are entirely maintenance- and wear-free, made from oxide-ceramic with optimal heat dissipation. Belt tensioning is provided by appropriately sized compression springs. Belt release for belt change is done via a pneumatic unit for gentle and distortion-free installation of new belts. The upper sanding and brush units are centrally and motor-driven height adjustable, with digital display at the control panel for motorized sanding thickness adjustment. Brush and finishing device, for improved surface finish, is integrated into the base machine. Two vertically arranged special brush rollers, 150 mm Ø, run in the direction of feed. Separate height adjustment of the brush rollers on precision carriage guides allows adjustment for wear compensation. An additional transport roller is provided for ejecting or further transporting the workpiece from the sanding machine, linked to the conveyor belt. Wood guiding at the infeed area for hard, double-sided...

Stanje: rabljeno, Tool Presetting Device GILDEMEISTER-DE VLIEG Type EGS 5045 / Microset DPS 100 Serial No. 83-10-102 Year of manufacture: 2002 Travel range X-axis: approx. 400 mm Travel range Z-axis: approx. 400 mm Tool holder on mounted rotary table: Ø 50 mm Pitch circle diameter of tool holders on mounted rotary table: Ø 340 mm Internal taper on mounted rotary table: Ø 245 mm Tool holding plate as rotary table with 8 mounting holes Ø 50 mm Centering diameter of installed tool holding plate: Ø 102 mm Rotatably mounted flange holder with centering diameter: Ø 102 mm Tsdpjhbal Dsfx Anpsd Rotatably mounted flange holder with outside diameter: Ø 155 mm Rotatably mounted flange holder with 3x M10 mounting holes, pitch circle: Ø 130 mm Power supply: 230 Volt, 50 Hz - Measuring electronics Microset DPS 100 - Rotary table with 8 tool positions - Interfaces: 1x RS232, 2x measuring system (X/Z) - Profile projector with screen Ø 100 mm, magnification 20x and two circular ground glass plates - Fixed ground glass with crosshairs - Axis movement via manual rapid adjustment with pneumatic clamping - Fine adjustment via handwheels - Rotatable rotary table with pneumatic clamping - Metal base with 3 drawers Required space (L x W x H): 1100 x 1000 x 800 mm Weight: 400 kg In good condition

Stanje: dober (rabljeno), Leto izdelave: 2006, Funkcionalnost: nepreverjeno, številka stroja/vozila: 06 03 1000, Country of manufacture: CH Voltage: 400V Dimensions: 1200 x 1650 x 2050 mm Net machine weight: 1900 kg TECHNICAL SPECIFICATIONS Machine: Table rotation speed: 0–110 rpm Max table drive power: 2 kW Max load on upper table: 20 daN Todpfx Anjw T Tpdjpjd Table diameter: Ø 450 mm Inner drive rotation speed: 0–115 rpm Max inner drive power: 0.5 kW Table drive motors (continuous-duty motor): Type: DC motor Armature voltage Ua: 260 V Field voltage Ue: 340 V Rotation speed: 3110 rpm Power: 2 kW External cooling: 220V, 50/60 Hz Inner drive motor: Type: Smooth-control center-drive motor Armature voltage Ua: 260 V Field voltage Ue: 340 V Rotation speed: 3110 rpm Power: 0.5 kW Separate ventilation: 220V, 50/60 Hz Vertical movement motor: Type: Stepper motor Steps per second: 50 Torque: 1100 Nm Crown gear adjustment: Type: AC brake motor Positions: 2 Voltage: 380V / 50 Hz Rotation speed: 700–1400 rpm Power: 0.25/0.37 kW DC brake: 24V Braking torque: 16 Nm Power converters: Input voltage: 380V / 50 Hz Induced voltage: 270 V Field voltage: 340 V Worm gear reduction ratio (inner drive) Ratio: i = 1 : 30 Worm gear reduction ratio (lower system) Ratio: i = 1 : 15.5 Worm gear reduction ratio (upper system) Ratio: i = 1 : 15.5 Operating pressure: Air circuit: 6–7 bar Lapping fluid pump: Mains connection voltage: 380V 50Hz Rotation speed: 2600 rpm Flow rate: 57 L/Min Protection: IP 44 Control and measuring device: Measuring range: 6 (±3 to ±11000 mm) See details in the Millitron operating manual Inductive sensor: Measuring range: ±2 mm Setpoint adjustment device: Display: 4-digit Unless otherwise stated, technical information is provided without commitment and subject to errors or omissions.

Leto izdelave: 2018, stanje: pripravljen za uporabo (rabljen), število osi: 2, Optični merilni stroj iz leta 2018. Ta KEYENCE IM 7030 ima vidno polje 300 x 200 x 150 mm in ponuja napredne programske funkcije, kot so serijsko merjenje, statistika/analiza in samodejno merjenje. Če iščete visokokakovostne optične merilne zmogljivosti, razmislite o napravi KEYENCE IM 7030, ki jo ponujamo v prodajo. Kontaktirajte nas za dodatne informacije. Tjdoy Enflopfx Anped • Tip sistema: Sistem za merjenje s sliko • Dimenzije vidnega polja: 300 × 200 × 150 mm • Programske funkcije: Serijsko merjenje; nastavitve meritev; statistika/analiza; posamezna meritev; samodejno merjenje

Leto izdelave: 2018, stanje: pripravljen za uporabo (rabljen), Ta optična merilna naprava KEYENCE IM-7030T je bila izdelana leta 2018. Opremljena je z 10,4-palčnim LCD-monitorjem, dvojnim telecentričnim objektivom in motoriziranima XY- in Z-mizama, z obsegom gibanja 200 × 100 mm oziroma 75 mm. Podpira tako način merjenja z velikim kotom gledanja kot tudi način merjenja z visoko natančnostjo, kar zagotavlja podrobne in natančne meritve. Izkoristite priložnost in kupite to optično merilno napravo KEYENCE IM-7030T. Za več informacij o tej napravi nas kontaktirajte. • Nadzorna enota: IM-7000 • Naprava za zajem slike: 1" 6,6 milijona slikovnih pik, monocromna CMOS • Zaslon: 10,4-palčni LCD-zaslon (XGA 1024×768) • Objektiv za sprejem svetlobe: Dvojni telecentrični objektiv • Sistem osvetlitve: Telecentrična svetloba, usmerjena navzdol, štiri-kotna osvetlitev (motorizirana), osvetlitev z režo (motorizirana) • Načini merjenja: Z velikim kotom gledanja, visoka natančnost • Obseg merjenja z velikim kotom gledanja: 300 × 200 mm (pravokotnik R50) • Obseg merjenja z visoko natančnostjo: 225 × 125 mm • Najmanjša enota prikaza: 0,1 µm • Natančnost merjenja (velik kot gledanja, brez gibanja mize): ±1 µm • Natančnost merjenja (visoka natančnost, brez premika mize): ±0,5 µm • Natančnost merjenja (velik kot gledanja, z gibanjem mize): ±2 µm • Natančnost merjenja (visoka natančnost, z gibanjem mize): ±1,5 µm • Kombinirana natančnost merjenja: ±(7 + 0,02L) µm (velik kot gledanja), ±(4 + 0,02L) µm (visoka natančnost) • Obseg merjenja (XY, miza): 90 × 90 mm • Največja globina merjenja: 30 mm • Premer tipala za svetlobo: 3 mm • Merilna sila: 0,015 N (tipalo za svetlobo), 0,3 N (merjenje višine) • Ponovljivost: ±2 µm • Obseg merjenja (Z): 0-75 mm Tjdpfsx D E Npsx Anpod • Natančnost merilne pozicije (XY): ±0,2 mm • Najmanjša enota prikaza (višina): 1 µm • Obseg merjenja (XY) v načinu z velikim kotom gledanja: 145 × 95 mm • Površina merjenja (XY) v načinu z visoko natančnostjo: 107,5 × 95 mm • XY-miza: Motorizirana, obseg gibanja 200 × 100 mm, največja obremenitev 5 kg • Z-miza: Motorizirana, obseg gibanja 75 mm • Zunanji vhod za daljinski nadzor: Vhod brez napetosti (kontakt/trdni element) • Zunanji izhod: PhotoMOS, OK/NG/FAIL/MEAS, nazivna obremenitev 24 VDC, 0,5 A • Vmesnik: LAN RJ-45 (10/100/1000BASE-T), USB 2.0 serija A (6 priključkov) • Pomnilnik za shranjevanje podatkov: HDD 500 GB • Temperatura okolja: +10 do +35 °C • Relativna vlažnost: 20-80 % RH (brez kondenzacije) • Stopnja onesnaženosti: 2 • Kategorija prenapetosti: II • Napajalna napetost: 100-240 V, 50/60 Hz • Teža glave: 31 kg • Teža nadzorne enote: ~8 kg

Stanje: novo, Leto izdelave: 2026, - Pametna varnost, čist zrak in večja učinkovitost. - Poskrbite za večjo varnost v svojem delovnem okolju s serijo TFON Airwet – vrhunskim mokrim sesalnim sistemom, zasnovanim za odstranjevanje isker in prahu, ki nastajata pri raziglevanju. Serija Airwet bistveno zmanjšuje tveganje požara in eksplozije ter ščiti vaše zaposlene ter obrat. - Preprečevanje požara in eksplozije: Učinkovito zmanjšuje nevarne delce in vire vžiga neposredno na izvoru. Tedpfx Anjvg U Dxsped - Izboljšana kakovost zraka: Zajema in odstranjuje škodljive delce v zraku ter tako prispeva k čistejšemu in zdravemu delovnemu okolju. - Enostavna integracija: Kompaktna, prostorsko varčna zasnova omogoča hitro namestitev v obstoječe stroje in delovne procese. - Večja varnost in skladnost s predpisi: Prispeva k izpolnjevanju zahtev glede varnosti in zdravja pri delu ter zvišuje celotno raven varnosti v obratu.

Stanje: rabljeno, Leto izdelave: 1975, Table diameter mm Workpiece height mm Number of wheels 2 Total connected load 11 kW Machine weight approx. 4.2 t Required space approx. m O F F E R We can offer you, ex stock and subject to prior sale and error, without obligation: HAHN & KOLB double-sided lapping and fine grinding machine Type ZL 800 H Year of manufacture approx. 1975 240 049 _____ Possible lapping/grinding wheel Ø 755 - 810 mm Possible wheel ring width 200 - 265 mm Currently installed wheel Ø / ring width 790 / 245 mm Max. transportation carrier wheel Ø approx. 306 mm Max. distance between cast lapping wheels 125 mm Max. distance between fine grinding wheels 83/78 mm Max. distance between mounting flanges 260 mm Lapping wheel speed upper 30 / 42 / 60 / 84 rpm Lapping wheel speed lower 30 / 42 / 60 / 84 rpm Workpiece carrier wheel central drive 28 / 40 / 56 / 80 rpm Spindle drive each 6 / 8 kW Total drive approx. 11 kW - 380 V - 50 Hz Weight approx. 4,200 kg Tsdpfx Anjub Al Ijped Special equipment / accessories: • HAHN & KOLB / LAUER measuring and control device with sensor routed through the hollow spindle. The sensor continuously measures during operation and automatically ends the cycle when the target thickness is reached. • Pressure stage adjustment via HELLER hydraulics and grinding phase adjustment via timer possible. • Currently fitted with fine grinding wheels for double-sided high-precision fine grinding of flat-parallel workpieces. • Side-mounted, height-adjustable and swiveling motorized dressing device with electric feed. • Lapping or rinsing agent dosing device with container • Multiple drive and pressure setting options such as: co-rotating / counter-rotating, individual drive, dragging one or both wheels, left/right rotation, etc. • Electrically height-adjustable planetary drive device for the carrier wheels Condition : mild noises in lower gearbox, otherwise in good condition Delivery : ex stock, immediately available, FCA Metzingen Payment : strictly net – payable upon receipt of invoice We have further double-sided lapping and fine grinding machines in stock, please contact us.

Stanje: zelo dobro (rabljeno), Prehodna brusilka Vertongen S320 Delovna širina: 300 mm Delovna višina do 180 mm Kombinirana enota s čevljem Tedpfxjyg Dlcs Anped Ročno dviganje in spuščanje delovne mize Dve hitrosti pomika: 7–14 m/min Glavni motor moči 5,5 kW

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2009, premer struženja nad prečnim suportom: 500 mm, izvrtina vretena: 75 mm, stružna dolžina: 1.000 mm, premer struženja: 500 mm, Oprema: vrtilna hitrost brezstopenjsko nastavljiva, Dormac CY-K500T Teachin draaibank Draaidiameter boven bed: 500 mm Doorlaat: 75 mm Draailengte: 1000 mm Transportafmetingen (LxBxH): 300x180x210 cm Gewicht: 2800 kg Besturing: Fagor Bouwjaar: 2009 Tsdpfx Ajrfxihonped Opties: Inclusief gereedschappen en documentatie Locatie: Hamont-Achel, België Bel of mail voor meer informatie Bekijk ook onze andere advertenties Wij zijn het hele jaar door op zoek naar industriële machines. Heeft u overbodige machines? Mail ze ons met foto's en informatie. --- Dormac CY-K500T Teach-in lathe Swing over bed: 500 mm Spindle bore: 75 mm Turning length: 1000 mm Transport dimensions (LxWxH): 300 x 180 x 210 cm Weight: 2800 kg Control: Fagor Year of manufacture: 2009 Options: Includes tooling and documentation Location: Hamont-Achel, Belgium Call or email for more information Please also see our other listings We are continuously looking for industrial machinery. If you have surplus machines, email us with photos and information. --- Dormac CY-K500T Teach-in-Drehmaschine Umlaufdurchmesser über Bett: 500 mm Spindeldurchlass: 75 mm Drehlänge: 1000 mm Transportmaße (LxBxH): 300 x 180 x 210 cm Gewicht: 2800 kg Steuerung: Fagor Baujahr: 2009 Optionen: Inklusive Werkzeuge und Dokumentation Standort: Hamont-Achel, Belgien Rufen Sie an oder schreiben Sie eine E-Mail für weitere Informationen Sehen Sie sich auch unsere weiteren Inserate an Wir sind ganzjährig auf der Suche nach Industriemaschinen. Wenn Sie überschüssige Maschinen haben, senden Sie uns bitte eine E-Mail mit Fotos und Informationen.

Stanje: novo, Leto izdelave: 2025, Moč laserja: 40000 W/30000 W/22000 W/20000 W/12000 W/6000 W/3000 W Primeren material: kovina Stanje: novo Tip laserja: vlakenski laser Delovno območje: 3048 mm × 1524 mm do 8100 mm × 2500 mm Hitrost rezanja: 200 m/min Podprti grafični formati: AI, BMP, DST, DWG, DXF, DXP, LAS, PLT Način hlajenja: vodno hlajenje Certifikati: CCC, CE, GS, ISO, SGS Blagovna znamka laserskega izvora: IPG/MAX Garancija: 3 leta Napajanje: 110V/220V/380V 50Hz/60Hz 1. Avtomatski menjalnik šob Stroj zamenja šobo v najhitrejšem času, v samo 35 sekundah – s tem prihranite 50 % stroškov časa. Tedpjg Ekddofx Anpod 2. Aktivna funkcija proti trkom Učinkovito zmanjšuje poškodbe laserske glave in vam pomaga prihraniti pri stroških vzdrževanja. 3. Obdelava z enim klikom Vse funkcije sistema so logično in pregledno razporejene, kar omogoča popolnoma avtomatizirano serijsko proizvodnjo. 4. Postelja iz sive litine Z odličnimi dušilnimi lastnostmi postelja iz sive litine ohranja svojo obliko in zagotavlja optimalno mehansko stabilnost.