Ergotech - sistem 250/280-80

DEMAG

Leto izdelave: 1995, stanje: dober (rabljeno), Electric chain hoist DEMAG DKUN 5-500-K-V1F4 Type: Electric chain hoist Godpfeudv Tkex Ab Eetw Year: 1995 Chain length: 3 meters Three-phase 380V Capacity: 1,000 kg 2 speeds (12.5 m/min - 6.2 m/min) 1.7 kW

Stanje: dober (rabljeno), Leto izdelave: 2011, Funkcionalnost: popolnoma funkcionalen, pomik po osi Z: 1.500 mm, Oprema: dokumentacija / priročnik, Število osi: 3 Gtedpfx Abjyfhw Hs Esw Doseg: 1500 mm Nosilnost: 5 kg X=420 mm Y=1200 mm Z=1500 mm

Stanje: rabljeno, DEMAG dvižni motor / motor za žerjav. Dvižni motor tip - KBH 100 B 8/2 - 2 kosa. Gjdpfx Absxpw Iuo Eetw

Stanje: zelo dobro (rabljeno), Leto izdelave: 2008, Injection Moulding Machine DEMAG System 800/1120-9500 Basic Information Manufacturer: DEMAG Model: System 800/1120-9500 Year of manufacture: 2008 Clamping Unit Clamping force: 8,000 kN Mounting platen dimensions (horizontal × vertical): 1620 × 1500 mm Tie bar spacing (horizontal × vertical): 1120 × 1000 mm Minimum mould height: 500 mm Maximum mould height: 1050 mm Gsdeyugctspfx Ab Eotw Maximum daylight between platens: 2080 mm Opening stroke: 1030 mm Ejector stroke: 350 mm Ejector force: 139 kN Maximum mould weight: 7,200 kg Injection Unit Screw diameter: 130 mm Shot volume: 7300 cm³ Shot weight (PS): 6640 g Maximum injection pressure: 1300 bar Screw length: 20 L/D Electrical and Hydraulic Equipment Pump drive rated power: 110 kW Heater power: 79 kW Hydraulic oil tank capacity: 1300 l Machine Dimensions and Weight Machine dimensions (L × W × H): 12.3 × 2.7 × 2.7 m Machine weight: 33,500 kg Control cabinet weight: 9,700 kg Optional Energy Saving System (ESS) The machine can be equipped with a modern ESS servo drive system, which increases the energy efficiency of hydraulic plastic injection moulding machines. The system controls the hydraulic pump motor operation via a frequency inverter, adjusting the motor speed to the current requirements of the production cycle. As a result, electrical energy is only consumed when the machine actually requires it. Key Benefits - Reduction of electricity consumption by up to 30% - Hydraulic pump servo drive technology - World-class, proven technology used in plastics processing industry - Reduced energy losses during idle - Lower hydraulic system temperature rise - Extended service life of hydraulic components - Suitable for retrofitting existing hydraulic injection moulding machines The ESS system significantly lowers machine operating costs while maintaining full production parameters.

Stanje: zelo dobro (rabljeno), Leto izdelave: 2008, DEMAG System 1500/1500-16000 Injection Moulding Machine Basic data Manufacturer: DEMAG Model: System 1500/1500-16000 Year of manufacture: 2008 Clamping unit Clamping force: 15,000 kN Platens dimensions (horizontal × vertical): 2150 × 1880 mm Tie bar spacing (horizontal × vertical): 1500 × 1250 mm Minimum mould height: 700 mm Maximum mould height: 1400 mm Maximum opening stroke: 2900 mm Injection unit Screw diameter: 145 mm Injection volume: 10,981 cm³ Shot weight (PS): 9,880 g Maximum injection pressure: 1454 bar Electrical and hydraulic equipment Pump motor rating: 165 kW Heater power: 97 kW Machine dimensions and weight Net machine weight: 74 t Control cabinet weight: 21 t Total weight: approx. 95 t Dimensions (L × W × H): 14.4 × 3.4 × 2.9 m Service history / repairs 2010 – new screw with RSP and barrel 2015 – new IBED Gsdpeyugalsfx Ab Eotw 2015 – new wiring board (cable plate) 2017 – new motor and pump no. 2 2017 – new injection cylinder piston rod with seals 2017 – replacement of oil cooler circulation pump 2017 – TeachBox (robot) replacement 2018 – replacement of P1 + P3 pumps (at 65,800 h) 2018 – hydraulic oil change Optional ESS Energy Saving System The machine can be equipped with a modern ESS servo drive system, significantly improving the energy efficiency of hydraulic injection moulding machines. The system controls the operation of the hydraulic pump motor using a frequency inverter, which adjusts the motor speed to match the machine’s actual demand during the production cycle. As a result, electrical energy is consumed only when it is actually needed. Key benefits: - Reduction of electricity consumption by up to 30% - Servo technology for hydraulic pump drive - World-class, proven technology used in plastics processing industry - Reduced energy losses during machine idle - Lower heating of hydraulic circuit - Extended service life of the motor and hydraulic components - Possible retrofitting to existing hydraulic injection moulding machines The ESS system allows for significantly reduced machine operating costs while maintaining full production capabilities.

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2013, obratovalne ure: 27.551 h, vpenjalna sila: 2.200 kN, skupna višina: 2.100 mm, This SUMITOMO SHI DEMAG IntElect 220/610-750 smart was manufactured in 2013. It is an electric injection moulding machine renowned for its precision and efficiency. Ideal for anyone looking to expand their production capabilities with reliable technology. Contact us for further information. Additional Equipment • Sepro robot SDR 22 Machine Advantages Technical Machine Specifications • Screw diameter: 45 mm / screw geometry: standard / l/d ratio: 20 / specific injection pressure: 2150 bar / max. shot volume: 329 cm³ / max. shot weight: 293 g / injection rate without accumulator: 254 cm³/s • Metering stroke: 207 mm / max. nozzle stroke: 450 mm / nozzle immersion depth: 20 mm / nozzle contact force: 58 kN / number of heating zones: 4 / hopper capacity: 50 l / max. injection speed: 160 mm/s • Clamping force: 2420 kN / max. opening stroke: 550 mm / min. mould height: 300 mm / max. mould height: 580 mm / max. platen distance: 1130 mm • Platen size (h x v): 880x830 mm / tie bar spacing (h x v): 610x560 mm / ejector stroke: 150 mm / ejector force: 58 kN Gtjdex D Hnyspfx Ab Esw • Dry cycle time according to Euromap 6 (stroke): 427 mm • Net weight without oil: 10,100 kg Dimensions Machine depth: 6460 mm

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2003, obratovalne ure: 96.986 h, vpenjalna sila: 600 kN, premer vijaka: 30 mm, This hydraulic injection moulding machine, model DEMAG ET60-200 concept, was manufactured in 2003. It features a clamping force of 600 kN and a maximum mould weight of 580 kg. The machine is equipped with a robust injection unit featuring a screw diameter of 30 mm and an injection pressure of 1900 bar. Take advantage of this opportunity to purchase the DEMAG ET60-200 concept hydraulic injection moulding machine. Contact us for further information. • Clamping unit: • Tie bar spacing (H x V): 420 x 420 mm • Platen dimensions (H x V): 530 x 540 mm • Min. mould installation height: 210 mm • Opening stroke: 400 mm • Max. mould weight: 580 kg (moving side 380 kg / fixed side 200 kg) • Ejector: • Stroke: 125 mm • Force: 41 kN • Retraction force: 15 kN • Pneumatic ejector: Yes • Core pull control: Yes (2 units, on ejector side/ES) • Injection unit 1: • Unit size: 200 • Screw diameter: 30 mm • Injection pressure: 1900 bar • Shot volume: 106 ccm • Shot weight (PS): 94 g • Screw L/D ratio: 20 • Nozzle radius: 15 mm • Armoured/wear-resistant injection unit: Yes • Process control: SPC (Yes) • Note: Maximum crane load warning: 2 tonnes Gjdpfoyg Nfuox Ab Eetw Additional equipment • Robot / parts removal device: W621-1381 • Strokes: Y 1200 mm, X 550 mm, Z 1500 mm • Hot runner controller: integrated 7-zone control • Tool sensors: Kistler (p=1/t=0)

Stanje: pripravljen za uporabo (rabljen), Leto izdelave: 2015, obratovalne ure: 15.642 h, premer vijaka: 45 mm, skupna višina: 2.213 mm, skupna masa: 15.750 kg, This SUMITOMO SHI DEMAG Systec SP 350/720-840 was manufactured in 2015. It is a hydraulic injection molding machine, ideal for precise plastics processing. Take advantage of the opportunity to purchase this SUMITOMO SHI DEMAG Systec SP 350/720-840 hydraulic injection molding machine. Contact us for further information. Additional Equipment • Fanuc robot Machine Advantages Qualitative Machine Advantages • Process data acquisition, mold protection Technical Machine Advantages • Minimum mold height: 350 mm / maximum mold height: 745 mm • Electronic main connection: 3/400 V 50 Hz • Programmable process, high dynamic feed speed, hydraulic pressure-dependent holding pressure control, digital/wear-free position measuring system. Additional Information Standard Equipment: Support of the moving platen via linear guides/ Short/long stroke ejector/ Interface for external printer (hardcopy)/ Individual axis motion optimization (activeAdjust)/ Four-stage mold closing and four-stage mold opening process/ Increased pump drive power II (59.0 kW)/ Mains voltage 400 V ±10% / 50 Hz, 3-phase + N + PE/ Separate mains connections for drive/heating/ Color data display/ Reinforced oil cooler (cooling water supply up to 35 °C)/ Separate water connections for mold and machine cooling/ Basic version Europe/ Corrosion protection/ Paintwork: Jet black (RAL9005): machine bed with installations, lower control cabinet/ Signal white (RAL9003): clamping unit, injection unit, nozzle protection/ Signal white (RAL9003): fixed safety devices, upper control cabinet/ Gedpex D Hntofx Ab Eotw Signal white (RAL9003): safety doors/ Structured Surfaces: Elastic machine mounts/ Digital and wear-free position measuring system (ultrasonic/high-resolution encoder for injection, mold, and ejector movement)/ Mold connection dimensions Type E (according to EUROMAP March '96)/ Centering diameter fixed platen: 160 mm/ Centering diameter moving platen: 160 mm/ No side ejector plate/ Standard Mold Installation Height: Min: 350 mm/ Max: 745 mm/ Standard closing speed (movements only when safety door closed)/ Ejector with position control (P/F+V independently programmable, parallel to mold movement)/ Oil lubrication of toggle lever/ Injection unit/ Optional Equipment: Speed-controlled pump Servo Technology (activeDrive)/ Emergency stop switch on operator side/ Separate opener for fine filtering in bypass (activeCool&Clean)/ Socket 1 x Schuko (230V / 10A), switchable via main switch/ Socket IECEE 3Ph / 400V-16A, switchable via main switch/ Warning light/ Operation with safety door open (operator side)/ 6 pneumatic 5/2-way valves on moving platen (programmable)/ 6 pneumatic 5/2-way valves on fixed platen (programmable)/ Central maintenance unit for pneumatic valves/ Core pull 1-circuit via proportional valve (programmable, with check valves)/ Manual pressure relief for core pull 1-circuit/ Operator-side safety guarding extended (250 mm)/ Hot runner control 12 zones, integrated (2.75 kW)/ Pneumatic hot runner nozzle control (1x 5/2-way valve)/ Clamping force regulation/ Active mold protection via sensor when closing (activeQ)/ Manually adjustable monitoring switch for mold open position/ Central grease lubrication (manual)/ Material hopper for automatic filling/ Hopper shut-off with discharge option/

Leto izdelave: 2019, obratovalne ure: 17.716 h, stanje: pripravljen za uporabo (rabljen), Splošni podatki Širina: 1920 cm Globina: 7750 cm Teža stroja: 26.210 kg Višina: 2410 mm Ta električni stroj za brizganje SUMITOMO SHI DEMAG El-Exis SP 350/820-920 je bil izdelan leta 2019. Robusten električni stroj za brizganje s premerom polža 40 mm in zapiralno silo 3.500 kN. Deloval je 17.716 ur in izvedel 12.440.761 ciklov, kar omogoča obsežne proizvodne zmogljivosti. Razmislite o nakupu električnega stroja za brizganje SUMITOMO SHI DEMAG El-Exis SP 350/820-920. Za več informacij nas kontaktirajte. Vrsta uporabe Brizganje plastike Gtodox D Nx Iopfx Ab Ejw

Leto izdelave: 2019, stanje: pripravljen za uporabo (rabljen), This DEMAG Systec 210/580-840 was manufactured in 2019. It is a hydraulic injection moulding machine with a clamping force of 210 tons and a power rating of 60 kW. The machine has been in operation for 31,132 hours. Consider the opportunity to purchase this DEMAG Systec 210/580-840 hydraulic injection moulding machine. Please contact us for further information. Godpfjx D Nlujx Ab Eetw • The dosing unit (orange part) is not included. • Integrated country-specific socket combination • Can be switched off via the main switch and shutdown program • 2 x Schuko 1Ph/230V/16A; 2 x IECEE 3Ph/400V/16A residual current circuit breaker • Pneumatic 5/2 valve no. 1 on the movable mould mounting platen; • Programmable, supplied via central air connection • Includes hoses. Inputs and outputs freely programmable; 3 inputs and 3 outputs; • Terminal point located outside the control cabinet • Interface for additional nozzle heating band; socket only • 2-circuit core pull via solenoid valve on the movable mould mounting platen; operation independent of clamping force (programmable); • With pilot-operated check valves to prevent core creep • Mould connection dimensions E (similar to Euromap March 96) • With side-mounted ejector plate, centering diameter of the fixed platen: 160 mm • Centering diameter of the moving platen: • Mold installation height increased by 100.0 mm • Min: 340 mm • Max: 790 mm